MSDS

ManualsBrandsROMAN ManualsHome DecorPRO-880 3.5-gal. Wallpaper Adhesive Kit for Large Sized Rooms

Reviewed 11-21-13

Product Data Sheet

Product Numbers: 12405, 12401

Base: Starch

General Properties: Premium clear, strippable

wallcovering adhesive that combines the best features

of clays and clears. It is excellent for the retail customer

as well as the most discriminating contractor.

• Maximum tack

• Extended open time

• Unsurpassed ease of clean up

• Spreads and flows easily

• LEED compliant

Recommended Uses: For all weights of wallcoverings.

Strippable when used with fabric backed vinyl over bare

drywall with a cure time of 6 weeks.

Compatible Coatings: All ROMAN

primers

Substrates: Apply over new, bare drywall or over a

ROMAN

primer.

All Roman products have a bactericide and

mildewcide for in-can protection. In addition, the

mildewcide provides on-the-wall protection.

SPECIFICATION DATA

Percent Solids: Approximately 32%

Coverage: Up to approx. 330 square feet per gallon

Viscosity: Approximately 40,000 - 45,000 cps

VOC: Zero (0 g/l)

Drying Time: Drying time will vary depending on the

temperature, ventilation and humidity of the room.

Storage: Avoid freezing; keep in cool, dry place.

LIMITED WARRANTY

Roman warrants that it will replace this product free of charge if, within

12 months of manufacture, it is found to be defective in material or

workmanship. This warranty is in lieu of any other. The exclusive

remedy is limited to the replacement of the product and Roman

disclaims all liability for consequential, punitive and special damages.

Conditions of use are beyond our control.

Roman Decorating Products • Calumet City, IL

Questions? Call 1-800-488-6117

www.romandecoratingproducts.com

-880, ULTRA

CLEAR

APPLICATION INSTRUCTIONS

Surface Preparation: Surface must be free from grease and other

residues, dry, smooth and structurally sound. Check surfaces for paint

bonding, loose wallcoverings, damaged wall- board or plaster. Repair

all unsound surfaces. Prime all surfaces (including oil-based coatings)

with ROMAN

PRO-977, ULTRA PRIME

. Priming of bare drywall is

not required with fabric-backed wallcoverings. Before proceeding with

any unusual conditions, consult your adhesive or wallcovering

supplier.

Tinting: N/A

Dilution: To use with pre-pasted wallcoverings, dilute with

1/2 gallon of clean water per gallon of adhesive. For some pasting

machines, thin with maximum of one pint of clean water per gallon.

Application Method: Use only when the room temperature is above

50°F. Apply an even coat of adhesive with a pasting machine, brush,

or roller. Avoid contact with the surface of embossed, textured or

delicate wallcoverings. Book wallcovering according to the wallcovering

manufacturerʼs instructions.

Drying Time: Varies, depending on the temperature, ventilation, and

humidity of the room.

Clean-Up: Before the adhesive dries, remove any excess with clean

water. Additional effort may be required if the adhesive is allowed to

contact the surface of embossed or textured vinyls.

WARNING -- Roman Decorating Products LLC does not

endorse the use of any product in an installation that does

not meet a Class A fire rating or any applicable code. Testing

by a certified laboratory should be conducted to verify the

installation meets a Class A fire rating and to guarantee

compliance with all applicable codes. Specifically, if a

Roman product is to hang wallpaper over existing wallpaper,

it is unlikely to meet these standards.

CAUTION

Do not freeze. Do not take internally. In case of ingestion,

seek medical attention. Avoid contact with skin and eyes. Use

of skin and eye protection is recommended at all times. If

contact with eye occurs, flush with water for 15 minutes. If

skin contact occurs, wash with soap and water. Seek medical

attention if rash or other symptoms occur. Do not mix with

other chemicals. Use in a well-ventilated work area. Close

container after each use. Keep out of the reach of children.

Summary of content (4 pages)

PAGE 1
Reviewed 11-21-13 Product Data Sheet PRO-880, ULTRA® CLEAR Product Numbers: 12405, 12401 Base: Starch General Properties: Premium clear, strippable wallcovering adhesive that combines the best features of clays and clears. It is excellent for the retail customer as well as the most discriminating contractor. • • • • • Maximum tack Extended open time Unsurpassed ease of clean up Spreads and flows easily LEED compliant Recommended Uses: For all weights of wallcoverings.
PAGE 2
Review Date: December 5, 2012 Material Safety Data Sheet Review Date: March 10, 2014 1. Product and Company Identification ® Product Name: Roman PRO-880 ULTRA Premium Clear Strippable Adhesive Product Application: Wallcovering adhesive Product Manufacturer: Roman Decorating Products LLC 824 State Street Calumet City, IL 60409 USA 1-800-488-6117 www.romandecoratingproducts.com Emergency Telephone Number: 1-800-488-6117 2.
PAGE 3
PRO-880 ULTRA® Premium Clear Strippable Adhesive Review Date: March 10, 2014 6. Accidental Release Measures Small spills of 1-2 gallons or less may be diluted 50:1 with water and washed down the drain. Large spills should be recovered as much as possible and disposed of as non-hazardous liquid waste. Remaining residues may be flushed away as in “small spill” procedure. Consult Federal, State, and Local regulations. Product residues may pose a slip hazard; personnel should be careful during clean-up. 7.
PAGE 4
PRO-880 ULTRA® Premium Clear Strippable Adhesive Review Date: March 10, 2014 11. Toxicological Information Acute toxicity: Relatively non-toxic, but see Section 3, Hazards Identification. Primary irritant effect: o Skin: mild irritant o Eye: mild irritant 12. Ecological Information This product can be handled as a non-hazardous industrial waste. Product should not be flushed to ground water or streams without normal sewage treatment. 13.