Product Brochure

www.roofaquaguard.com
Marketing, Sales & Technical Support:
Nemco Industries Inc.
4655 Caulfeild Drive
West Vancouver, BC V7W 1E9
Tel: [phone]
[e-mail]
Manufactured for:
All material must be installed in
compliance with applicable codes
and ordinances
INSTALLATION INSTRUCTIONS:
Peel and stick ice & water guard
SUBSTRATE PREPARATION:
APPLICATION GUIDELINES
Lemminkäinen Rakennustuotteet OY
PL 10,
04361 Tuusula, Finland
NO MORE LEAKY SEAMS
This Peel and Stick product is specifically designed to cater for the growing Metal and
Tile markets, but is also user friendly with other roof coverings.
Use under Metal or Tile
RoofAquaGuard MT
s Coated with a Green“Non-Slip” fiber felt cover,
a Peel and Stick Polyester carrier and a SBS
Modified Bitumen
s Has a split release film
s Excellent adhesion properties
s Has been approved by Dow Chemical Co.,
when installing Tile, to be fastened with their
“Tile Bond” foam adhesive.
s Will not adhere to Metal panels
s Can be installed in cool temperatures down to
+45° F and can withstand temperatures of up
to +280° F
s Can be left uncovered & exposed to the
elements for up to 180 days
s One of the few peel and stick products which
fully comply to the ASTM D1970 specifications
and requirements, such as prevention of
moisture ingress through the overlapped
selvedge edge
s Limited 35 Year warranty
s $O NOT INSTALL UNDERLAYMENTS DIRECTLY ON OLD ROOF COVERING
s #HECK WITH THE -ANUFACTURER OF -ETAL 2OOFING FOR ANY SPECIAL
requirements when underlayment is installed under metal
roofing which do not have proper ventilation.
s 5NDERLAYMENTS ARE AIR AND VAPOR BARRIERS THEREFORE ALWAYS
provide proper roof insulation and ventilation.
s 2EPAIR HOLES TEARS AND DAMAGE TO MEMBRANE WITH A ROUND
patch of membrane extending past the damaged area 6 inches.
s -AY BE APPLIED DIRECTLY TO PLYWOOD WOOD COMPOSTION BOARD
polyisocyanurate, extruded and expanded polystyrene insulation,
gypsum sheeting and wood plank.
s For best adhesion, lightly prime wood and masonry substrates.
s Primer must be fully cured prior to membrane application.
s Deck may not have voids or areas that are unsupported.
s Deck must be clean and dry or loss of adhesion may occur.
s !LWAYS START INSTALLATION FROM THE LOWEST PART OF THE ROOF DECK
s !LIGN THE MEMBRANE ON THE LOWER EDGE OF ROOF
s 0ULL BACK THE SPLIT RELEASE FILM TO EITHER SIDE OF THE MEMBRANE
s &OR IMPROVED ADHESION ROLL OVER EDGES AND SEEMS WITH A HAND ROLLER 5SE A FLAT
broom, or squeegee to help lay flat and adhere the field of the underlayment.
s 6ALLEY AND 2IDGE APPLICATIONS #ENTER THE SHEET OVER VALLEY OR RIDGE PEEL BACK
the split release film and press firmly into place. Always start from the lowest
point on the valley applications.
s 7HERE NAILING IS NEEDED FOR STEEP SLOPE APPLICATIONS BACKNAIL AND COVER NAILS
by overlapping with the next sheet.
s %ND LAPS MUST BE AT LEAST  INCHES AND SIDE LAPS MUST BE AT LEAST  INCHES
s For best adhesion, apply in minimum 45˚F or higher.
s 3TORE ROLLS AT TEMPERATURES BETWEEN  AND  &AHRENHEIT
Refer to peel and stick high temperature manufacturer’s installation instruc-
tions. All Material must be installed in compliance with applicable codes and
ORDINANCES !PPROVALS -EETS !34- $
PRECAUTIONS and LIMITATIONS:
s !LWAYS WEAR FALL PROTECTION WHEN WORKING ON A ROOF DECK
s !LL UNDERLAYMENTS CAN BE SLIPPERY WHEN WET OR COVERED BY FROST
s 2EMOVE RELEASE LINERS SOONEST POSSIBLE FROM WORK AREA AS THEY CAN
be slippery.
s &OLLOW MAXIMUM RECOMMENDED EXPOSURE GUIDELINES WHEN
exposing underlayments to sunlight.
s $O NOT FOLD UNDERLAYMENTS OVER THE REOOF EDGE UNLESS IT IS
protected by flashing material.
SAFETY, STORAGE and HANDLING
s 2EAD ALL PRODUCT LABELS AND -ATERIAL 3AFETY $ATA 3HEETS -3$3
for proper handling and disposal.
s $ELIVER ALL MATERIALS IN MANUFACTURERS UNOPENED PACKAGES
s 0ALLETIZED MATERIAL SHOULD BE STACKED ONLY TWO HIGH
s 3TORE ALL MATERIALS UNDER COVER
s !VOID PROLONGED STORAGE ABOVE # &
ProductsProducts
!
"
#
"
$
%
&
'
(
)
)
(
*
$
+
,-
+%()