Assembly Instruction

ManualsBrandsRoom & Board ManualsBedroomRoom & Board Perspective

ASSEMBLY INSTRUCTIONS

For MODA LOFT

DO NOT USE POWER TOOLS!

Steps 2-4:Bedrail Step 11: Ladder

Step 5: Slatroll

Steps 6-8: Lower Sections

Step 10: Guardrails

Assemble Loft Bed

Step 1: Assemble the Upper Section (Bed) of the Loft first. Use the 2 Loft Bed

Panels as the ends of the bed.

Step 2: Insert a Wood Dowel into the middle hole of each trio of holes on

both Panels. Screw a Connector Bolt into each of the threaded inserts, leaving

four or five threads exposed.

Step 3: Align connector bolts with the holes on the end of a Bedrail, slipping

bolts through pre-drilled holes in the Bedrail. Repeat on other side. Make sure

each Bedrail is tight up against the panel.

Step 4: Through the large hole in the side of the Bedrail, slip one metal collar

over each connector bolt. Use the ball-end Allen wrench to start each bolt,

then switch to the short end to finish tightening completely.

Step 5: Unroll and lay the Slatroll inside the Bedrails, with the webbing facing

up. With the 24 Wood Screws provided, attach the slats. The first slat must

be 2 inches from the end of the Bedrail. Pull the Slatroll taught and secure the

other end 2 inches from the end of the Bedrail on that side; then secure all other

slats. The slats should be centered between the Bedrails, with a 1/8” gap

between the end of the slat and the Bedrail. This permits the Guardrail bracket

to slip in between the slat and the Bedrail.

Arrange and secure Lower Sections

Step 6: Connect Desk Panel to Tall Panel and Bookcase in desired orientation

using 4 of the 40MM bolts.

Step 7: 2 Adhesive Tabs may be used to cover the remaining holes.

Step 8: Insert 2 Steel Pins into the holes on top of the Tall Panel.

Place the Bed on top of the Lower Sections

Step 9: Lift the bed and place it on top of the lower sections using the

Steel Pins to align the Panel of the bed with the Tall Panel beneath it. Secure the

Bookcase to the other end of the bed by using 2of the 40MM bolts to screw up

through the Bookcase top and into the insert in the Bedrail, and 2 more bolts to

screw up through the Bookcase top and into the insert in the bottom of the Bed

Panel. Get all 4 bolts started before tightening any. Tighten securely.

Step 10: Place the Long Guardrail on the wall side of the bed so that the

brackets are on the inside of the Bedrail, and attach each bracket with 2 Screws.

Place the Short Guardrail on the front Bedrail against one of the Footboards.

(This allows an opening for the Ladder at the other end.) Screw the Short

Guardrail brackets to the inside of the Bedrail.

Step 11: Attach the Ladder by hooking the bracket over the Bedrail. Use 2

wood screws to secure the bracket to the inside of the Bedrail.

Step 12: Mattress may be placed with or without a platform board on Slatroll.

Summary of content (4 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS For MODA LOFT DO NOT USE POWER TOOLS! Steps 2-4:Bedrail Step 11: Ladder Step 5: Slatroll Steps 6-8: Lower Sections Assemble Loft Bed Step 1: Assemble the Upper Section (Bed) of the Loft first. Use the 2 Loft Bed Panels as the ends of the bed. Step 2: Insert a Wood Dowel into the middle hole of each trio of holes on both Panels. Screw a Connector Bolt into each of the threaded inserts, leaving four or five threads exposed.
PAGE 2
Use only mattress which is 74”-75” long and 37 ½”-38 ½” wide on upper bunk. Ensure thickness of mattress and foundation combined does not exceed 7” and surface of mattress is at least 5” below upper edge of guardrails. Replacement parts, including additional guardrails, may be obtained from any Room & Board store. SAFETY WARNINGS Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.
PAGE 3
PARTS FOR LOFT BED 2 – LOFT BED PANELS 2 – LOFT BEDRAILS 1 – SHORT GUARDRAIL 1 – LONG GUARDRAIL (screws enclosed in cardboard pad on bracket) 1 – SLATROLL 1 – LADDER HARDWARE Bag in Slatroll Box: 4 – WOOD DOWELS 24 – WOOD SCREWS (1 ¼”) Bag in Loft Bedrail Box: 12 – DECORATIVE BOLTS (40 MM) 8 – CONNECTOR BOLTS (60 MM) 8 – METAL COLLARS 1 – BALL END ALLEN WRENCH 8 – ADHESIVE TABS (18 MM) 2 – STEEL PINS 2 – WOOD SCREWS (1”)
PAGE 4