Full Product Manual

01.31.2017 | Page 1
CARE & MAINTENANCE
Roppe Corporation | 1602 N. Union St. - Fostoria, OH 44830 | (800) 537 - 9527
TV WALL BASE
vinyl base
Maintenance Overview
Vinyl wall base does not typically require specialized
maintenance within the parameters of a maintenance
program. However, these products may require occasional
cleaning, which is usually consistent with the adjoining floor
covering. The frequency of daily and routine maintenance
will depend upon the amount and type of traffic and wear
in the area.
When installing Vinyl wall base in areas where desks, chairs
and or furniture with castors will be used or in areas where
auto-scrubbers and/or vacuums will be used, it is extremely
important to protect the base from unnecessary damage
due to moving furniture or equipment. Whenever possible,
prevent damage and abuse to wall base.
Always use untreated, new or thoroughly cleaned cloth
when conducting daily or routine maintenance. Do not
use Kerosene, Gasoline, Naphtha and/or other solvents
to clean wall base. As with any maintenance program, be
sure to use proper PPE (Personal Protective Equipment)
per the cleaning product SDS and ensure all maintenance
procedures are conducted per the cleaning products
instructions.
1. POST-INSTALLATION CHECKLIST
• When moving furniture or heavy equipment, protect wall
base from scuffing and scratching that may not come out
during the maintenance procedures.
• DO NOT use vacuums or electric brooms which have
beater bars, hard plastic bottoms, a rubber bumper or
are lacking proper padding or protection, as this may
cause marking, discoloration, scratching and loss of
sheen.
• DO NOT use detergents, abrasive, alkaline or acidic
cleaners, cleaning agents which contain oil or solvents,
as well as “mop and shine” type products, as they will
dull the finish and sheen and potentially damage the
wall base material.
• DO NOT clean area per the adhesives traffic limits (48-72
hours) to allow proper curing of the adhesive.
• DO NOT flood the area when cleaning.
• DO NOT allow the cleaning solution or topical moisture
to work its way beneath the material, as this can result in
an adhesive and/or installation failure.
2. INITIAL MAINTENANCE
Ensure that adhesive has cured for recommended period
of time prior to conducting initial maintenance. Remove
any protective coverings prior to cleaning. Sweep, dust or
wipe material to remove any dirt, dust or debris. DO NOT
use vacuums or electric brooms which have beater bars,
hard plastic bottoms, a rubber bumper or are lacking
proper padding or protection, as this may cause marking,
discoloration, scratching and loss of sheen. Do not use
detergents, abrasive cleaners or “mop and shine” type
products, as they will dull the finish and sheen of the material.
Additional Information
Approved Cleaners
• Excelsior NC-900 Neutral Cleaner
Approved Finish Removers
• Excelsior FR-920 Finish Remover
Technical Documents & Support
Additional product resources and technical documents
are available online at roppe.com. For additional technical
support, send an e-mail to [e-mail].
Mix 2-4 ounces of Excelsior NC-900 Neutral Cleaner per
gallon of clean, potable water. Use a clean towel or cloth
to apply cleaner to material. If heavily soiled, an additional
cleaning may be required. Use clean towel or cloth to remove
any and all excess cleaning solution. Rinse area with clean,
cool water and allow material to dry entirely. Ensure material
is clean and that all cleaning residue has been removed (this
may require additional rinsing).
3. DAILY MAINTENANCE
Ensure that initial maintenance has been conducted prior
to conducting daily maintenance. Sweep, dust mop or wipe
material to remove any dirt, dust or debris.
Mix 2-4 ounces of Excelsior NC-900 per gallon of clean,
potable water. Use a clean mop or cloth to clean spills,
dirt buildup and other debris. Allow material to dry before
allowing foot traffic.
4. MATERIAL PROTECTION
Protect newly installed material with construction grade
paper or protective boards, such as Masonite or Ram Board,
to protect material from damage by other trades. Limit usage
and foot traffic according to the adhesive's requirements.
When moving appliances or heavy furniture, protect wall base
from scuffing and tearing using temporary floor protection.
For more information regarding cleaner application
or finish removal, please consult the associated
Excelsior product data sheet.