Owner Manual

ManualsBrandsRosalind Wheeler ManualsAccent Furniture44.25" Solid Wood Console Table

WARNING!!

Furniture Tipping Risk.

Serious risk of severe or fatal crush injuries can occur from

furniture tipping over if not secured.

Children like to climb on furniture and Unsecured furniture

can pose a serious danger.

Please follow all instructions and install the tip-over

restraints provided.

In addition to installing the restraints, to help prevent tipover:

1. Unless specifically designed to accommodate, do not set

TV’s or other heavy objects on top of this product.

2. Never allow children to climb or hang on top glass.

3. Do not step on the Table base

Page 1 OF 10

Summary of content (10 pages)

PAGE 1
WARNING!! Furniture Tipping Risk. Serious risk of severe or fatal crush injuries can occur from furniture tipping over if not secured. Children like to climb on furniture and Unsecured furniture can pose a serious danger. Please follow all instructions and install the tip-over restraints provided. In addition to installing the restraints, to help prevent tipover: 1. Unless specifically designed to accommodate, do not set TV’s or other heavy objects on top of this product. 2.
PAGE 2
Caution : You must read this before you proceed CONSOLE Label Picture Description QTY A Top Panel 1 B Left Leg 1 C Center Strip 1 D Right Leg 1 Page 2 OF 10
PAGE 3
Label Picture Description QTY ① Washer 7 ② Bolt (M8x50mm) 7 ③ Spanner 1 4 Screwdriver (not provided) 1 5 Hammer (not provided) 1 6 Power Drill (not provided) 1 7 Bracket 2 8 Wall Plug Screw (M6x16mm) 4 9 Wall Plug (10x38mm) 4 10 Restraint Strap 2 Page 3 OF 10
PAGE 4
Before Beginning Assembly: Overview TopPanel (A) Right Leg (D) Left Leg (B) Center Strip(C) FRONT FACING Page 4 OF 10
PAGE 5
This Console Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Console parts, the above picture is to help you put the various parts into perspective. Please read through the instructions herebelow to familiarise the parts and steps before assembly. Step 1 Unpack and place all parts on a clean, non-marring surface. Step 2 B A Place the Top Panel (A) upside down onto a clean, soft surface to avoid any scratches or damages to the product.
PAGE 6
Step 3 Then continue position Center Strip (C) as shown in picture above. Alocate the holes of Left leg ( B). Then affix by using Washer (①) and Bolts (②) with help of Spanner (③). Step 4 D B A Align the mounting of Top Panel (A) into Right Leg (D) as shown above.Then affix the Top Panel (A) with Right Leg (D) and Center Strip (C) with Right Leg(D) by using Washer(① ) and Bolt ( ②) with help of Spanner (③ ).
PAGE 7
Step 5 ROTATE THE PIECE UPSIDE DOWN. CAUTION 1: When tightening these Bolts, tighten sequentially. If there is still wobbles, loosen the Bolts and execute this same process.Ensure all Bolts are fully locked into position. Caution 2: This Console Table can only be used on a flat, level surface.
PAGE 8
Step 6 6.1) Drill two holes on wall at same height as Brackets (⑦) on console with Power Drill (⑥). You can mark these points in two ways as below: 1) Move the Console back to the wall. Mark two points same height as console on the wall. Note: The Brackets need to be secured to solid, load bearing surface. Please use a Stud Finder(not supplied) if needed to locate the Wall Frame. 2) Measure the height of the Brackets (⑦) with ruler/measuring tape and mark on wall to keep them accurate and same height. 6.
PAGE 9
Console Restraint Device Installation Instructions Serious or fatal crushing injuries can occur from tipping furniture. To help prevent tip-over: ALWAYS secure this furniture to the wall using Cabinet Restraint Device. See product instructions for more ways to help prevent furniture tip-over. Usage For Console Restraint Device: To secure Console against wall, attach two Brackets (⑦) on wall and product, use Restraint Strap (⑩) to connect the Brackets (⑦).
PAGE 10
Attach Brackets (⑦) to Wall Plugs (⑨) using Wall Plug Screws (⑧) with Screwdriver (④). Step 8 Move Console Table to the wall. Pull the Restraint Straps ⑩ through the Brackets (⑦) on the wall and Console table one by one, and pull the Restraint Straps (⑩) tight. This Console Table is now ready to use. Caution: This Console can only be used on flat, level surface.