ROSCO DELTA 6000™ Operation Manual Revision 1.0 October, 2004 ROSCO LABORATORIES, INC. 52 Harbor View Avenue, Stamford, CT 06902, USA (800) ROSCONY, (203) 708-8900, Fax: (203) 708-8919 email: info@rosco.
ROSCO DELTA 6000™ FOG MACHINE OPERATION MANUAL Information in this document is subject to change without notice and does not represent a commitment on the part of Rosco Laboratories, Inc. © 2004 by Rosco Laboratories, Inc. Edition of October, 2004. This manual covers the following products: ROSCO DELTA 6000™ FOG MACHINE TABLE OF CONTENTS INTRODUCTION ............................................................................................…2 HOW THE MACHINE WORKS .......................................
INTRODUCTION This manual offers a detailed explanation of the operation of the ROSCO DELTA 6000™ fog machine. To assure efficient and safe operation, please take a few minutes to read this material. The ROSCO DELTA 6000™ fog machine is a thermal aerosol generator designed for very high variable fog output. It features the DELTA TECHNOLOGY™ which is a revolutionary electronics design unmatched by any other fog machine.
IMPORTANT SAFEGUARDS READ AND UNDERSTAND THESE SAFETY PRECAUTIONS BEFORE OPERATING THE MACHINE. FAILURE TO PROPERLY FOLLOW THESE PRECAUTIONS MAY LEAD TO A FIRE, EXPLOSION, OR ELECTRICAL SHOCK. FOG FLUID HEALTH CAUTION: VAPOR FROM THIS FLUID, LIKE ANY OTHER COMMON MATERIAL IN A VAPORIZED STATE, MAY BE IRRITATING TO OR CAUSE ALLERGIC SYMPTOMS IN SOME PERSONS WITH ALLERGENIC SENSITIVITY. DO NOT EXPOSE AT CLOSE RANGE TO KNOWN ASTHMATICS. 1.
7. Machines are designed for continuous use over an 8-hour day, but to protect components, it is wise to turn off the machine when it is not in use. In permanent installations, it is advisable to equip the circuit with a night cut-off device. 8. During the warm-up phase and during operations, people should not stand within three feet (one meter) of the front of the machine. Flammable material like paper, fabric, etc.
GENERAL OPERATING INSTRUCTIONS OVERVIEW The Delta 6000 fog machine is a unique fog system that consists of a base unit that can operate from any of three remote controls. Because of the variation in operability between the different remotes, there is an operations section for each remote. First follow the General Operating Instructions and then go to the section for the remote that is being used. If there is doubt about which remote is being used, please reference the picture in each section.
simply an indication to the operator that the fluid level should be checked and will not affect the performance. Because the bottles will “self-level” a Low Fluid Sensor is only required in one bottle. Pump Cut Off: The Delta 6000 is also equipped with a thermal cut-off that is attached to the pump. If the machine is running when the fluid bottle is empty, the pump could start to overheat at which time the thermal sensor will cut off power to the pump.
DIGITAL/DMX REMOTE CONTROL OPERATING INSTRUCTIONS ARROW buttons LCD display POWER button Jog wheel TIMER button Fog RUN button ENTER button Fog MOMENTARY button DIGITAL/DMX REMOTE CONTROL OVERVIEW The DIGITAL/DMX REMOTE CONTROL is a sophisticated digital interface that allows the the Delta 6000 to be operated: manually (MANUAL MODE); from timers (TIMER MODE); from DMX control (DMX MODE); or from a 0-10 volt signal. The interface is a backlit liquid crystal display (LCD) showing a series of commands.
button once. The Language Menu will display. Push an ARROW button to scroll through the language choices. When the desired language is displayed, push the ENTER button. 9. MANUAL MODE To produce fog manually: With the Operation Menu displayed, push the RUN button or the momentary (MOM) button located on the remote control. Push the RUN button again to stop producing fog. (The momentary button will stop producing fog as soon as it is released.
The Rosco Delta 6000 has the option to be operated from a lighting control console using USITT DMX 512/1990. Attaching DMX cable: Plug a standard 5-pin DMX cable to the connection marked DMX IN at the rear of the base unit. Note that the DMX signal can pass through to another device by plugging another cable into the DMX OUT plug. Note: Like any DMX controlled device, if the Delta 6000 is the last device in the DMX line then a terminator plug must be plugged into the DMX OUT connection.
ANALOG/DMX REMOTE CONTROL OPERATING INSTRUCTIONS DMX Rotary Knobs DMX LED POWER LED FOG LED POWER Button TIMER LED FOG Switch TIMER Button ON TIME Knob OFF TIME Knob VOLUME Control ANALOG/DMX REMOTE CONTROL OVERVIEW The ANALOG/DMX REMOTE CONTROL is an analog interface that consists of an array of switches and knobs. These allow the Delta 6000 base unit to be operated: manually; from timers; from DMX control; or from a 0-10 volt signal.
14. TIMERS The ANALOG/DMX REMOTE CONTROL is equipped with timers to automatically sequence the fog. To set the amount of time that the machine will make fog, turn the knob marked ON TIME. The longest time that the ANALOG/DMX REMOTE will make fog is 2 minutes. By experimenting with the knob, the desired time can be determined. To set the amount of time between bursts, turn the knob marked OFF TIME. The longest time between bursts is 4 minutes.
TIMED REMOTE CONTROL OPERATING INSTRUCTIONS POWER LED FOG LED POWER Button TIMER LED FOG Switch TIMER Button ON TIME Knob VOLUME Control OFF TIME Knob TIMED REMOTE CONTROL OVERVIEW The TIMED REMOTE CONTROL is an analog interface that consists of an array of switches and knobs. These allow the Delta 6000 base unit to be operated: manually; from timers; or from a 0-10 volt signal. The timers will allow production of fog for up to 2 minutes with intervals of up to 4 minutes between bursts.
The TIMED REMOTE CONTROL is equipped with timers to automatically sequence the fog. To set the amount of time that the machine will make fog, turn the knob marked ON TIME. The longest time that the TIMED REMOTE will make fog is 2 minutes. By experimenting with the knob, the desired time can be determined. To set the amount of time between bursts, turn the knob marked OFF TIME. The longest time between bursts is 4 minutes. By experimenting with the knob, the desired time can be determined.
DO'S & DON'TS DO Read the entire manual before operating the machine and pay particular attention to all CAUTIONS AND WARNINGS. DO Use ONLY Rosco brand fog fluids. DO Use an extension cord which is properly rated for voltage, current and length and which is free from nicks or other signs of wear. DO Before each operating period, check to see that the machine is clean and free of foreign objects. DO Test first for dry fog.Turn the FOG switch on.
MAINTENANCE 1. The main fuse of the ROSCO DELTA 6000 Fog Machine is located on the circuit card inside the machine. NOTE: Be sure to check the specifications when replacing any fuses. WARNING: DISCONNECT THE ROSCO DELTA 6000 FROM POWER BEFORE CHECKING OR REPLACING THE FUSE. FAILURE TO DO SO COULD BE HAZARDOUS AND RESULT IN AN ELECTRICAL SHOCK. 2. After every operation, the siphon hoses should be removed from the external reservoirs. The machine should be turned on and fog produced.
ROSCO OFFICES WORLDWIDE If the machine fails and repairs are required, call or write the nearest Rosco office (listed below) or your local Rosco dealer. UNITED STATES World Headquarters Rosco Laboratories, Inc. 52 Harbor View Avenue Stamford, CT 06902 (203) 708-8900 (800) 767-2669 E-mail: info@rosco.com UNITED KINGDOM Roscolab, Ltd. Blanchard Works Kangley Bridge Road Sydenham, London SE26 5AQ England (81) 659-2300 E-mail: marketing@roscolab.co.uk Rosco Laboratories, Inc. 1120 N.
LIMITED WARRANTY ROSCO LABORATORIES warrants to the original purchaser that the ROSCO DELTA 6000 FOG MACHINE base unit and any associated remote controls will be free from original defects in workmanship and material for a period of two (2) years from the date of purchase. During the warranty period, machines will be repaired or replaced at the option of Rosco.
DIGITAL/DMX REMOTE CONTROL MENU FLOWCHART NOTE: To navigate within a given menu or submenu window (i.e., choosing a language in the Language Menu) use the ARROW buttons. OPERATION MENU ENTER LANGUAGE ENTER SET TIMER? YES ON TIME ENTER OFF TIME ENTER NO SET DMX? NO YES DMX ADDRESS ENTER SAVE SETTINGS? NO YES LEGEND MENU SUBMENU COMMAND PAGE 18 www.rosco.
ROSCO DELTA 6000 TECHNICAL SPECIFICATIONS POWER REQUIREMENTS 120 volts, 60 Hz, 15 amps, 1500W 230 volts, 50 Hz, 10.5 amps, 2400W PARTICLE SIZE 0.25-60 microns DIMENSIONS Height: 9 in. (22.9 cm) Width: 14.5 in. (36.8 cm) Length: 25 in. (63.5 cm) WEIGHT 35 lb. (15.9 kg) MAX. FLUID CONSUMPTION 193 ml/minute MAIN FUSE 120 volt: 16A/250v 240 volt: 12A/250v REMOTE CONTROLS DIGITAL/DMX REMOTE: Multi-lingual Volume Control Timers On time: 0:01-9:59 min. Off time: 0:01-59:59 min.
