CrystalView™ DVI Fiber DIGITAL FIBER KVM EXTENDER INSTALLATION AND OPERATIONS MANUAL Single or Dual video / USB or PS/2 / Singlemode or Multimode models 10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.
LIMITED WARRANTY Rose Electronics warrants the CrystalView DVI Fiber to be in good working order for one year from the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All replaced parts become the property of Rose Electronics.
FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERENCE STATEMENTS Models: CRK-2DFMPD1D CRK-2DFMPD2D CRK-2DFMUD1D CRK-2DFMUD2D CRK-2DFSPD1D CRK-2DFSUD1D CRK-2DFSPD2D CRK-2DFSUD2D CRK-2DFMPD1D/3.2 (3.2 GBit model) This equipment generates, uses and can radiate radio frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer’s instructions may cause interference to radio communication.
TABLE OF CONTENTS Contents Disclaimer ......................................................................................................... 1 System introduction .......................................................................................... 1 Features............................................................................................................ 2 Compatibility .....................................................................................................
INTRODUCTION Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein. The manufacturer reserves the right to change the specifications, functions, or circuitry of the product without notice.
Features Perfect image quality at resolutions up to 1920 x 1200 @ 60Hz using fiber optic cable Extend a KVM station from a CPU up to 33,000 feet (10,000m) (6,500 feet, 2,000m for the 3.2 GBit model) Supports PS/2 or USB keyboard and mouse (Depending on model) Supports all DVI graphic cards and monitors Ideal for use with today’s digital flat panel monitors 24 Bit Color Single and dual video models available The CrystalView DVI Fiber uses a microprocessor to emulate the keyboard and mouse.
MODELS Models / Connectors (Single Video) PS/2 Transmitter (2-DVI-I / 1-MiniDin6 – “Y” cable needed) PS/2 Receiver (1-DVI-I / 2-MiniDin6) USB Transmitter (2-DVI-I / 1-USB type B) USB Receiver (1-DVI-I / 2-USB type A) Transmitter / Receiver (1-Power / 1-Fiber type LC) CRYSTALVIEW DVI FIBER INSTALLATION AND OPERATIONS MANUAL 3
Models (Dual Video) REAR PS/2 Transmitter (4-DVI-I / 1-MiniDin6) PS/2 Receiver (2-DVI-I / 2-MiniDin6) USB Transmitter (4-DVI-I / 1-USB Type B) USB Receiver (2-DVI-I / 2-USB Type A) FRONT Transmitter (Front-All) (1-Power / 2-Fiber type LC) Bottom connector carries video 1 and keyboard/mouse data, top connector carries video 2.
CABLES Cables (See Attachment B for cable part numbers) Transmitter unit to CPU cable CPU cables connect from the transmitter to a CPUs keyboard, video monitor and mouse ports. A “Y” PS/2 cable for the keyboard and mouse are needed. Receiver to KVM station cable The keyboard, video monitor, and mouse cables on a KVM station can connect directly to the receiver or a transmitter with local KVM access.
INSTALLATION Installation Please refer to the safety section first before proceeding with any installation or configuration of the CrystalView DVI Fiber. When installing the CrystalView DVI Fiber, locate the transmitter as close as possible to the CPU or switch. Keep the cables as short as possible but still give some freedom of movement. You can mount the CrystalView DVI Fiber in a CPU rack with the optional rack mount kit.
Connect the local USB model transmitter as shown below (single or dual video). A USB hub is used for local keyboard and mouse connections to the computer. nd To 2 DVI Graphic card st To 1 DVI Graphic card nd To 2 DVI local monitor st To 1 DVI local monitor To CPU USB or USB hub for keyboard and mouse Transmitter to Receiver cabling Cable type 62,5µm Multimode-Fiber 50.0µm Multimode-Fiber 9.0µm Singlemode-Fiber 9.
INSTALLATION Diagnostic LED Indicators POWER DATA ERROR STATUS VIDEO OK Power (Red) Off – No power applied, device not ready On- Power applied, device ready Data Error (Green) • Off - No errors, device ready • Blinking / On – Transmitter / Receiver communication not established Link Status (Green) • Blinking – No Fiber cable connection detected • On – Transmitter / Receiver communication established, device ready Video OK (Green) • Off – No video signal detected • On – Video signal detected, device
OPERATION INSTRUCTIONS Operating instructions Operation of your computer is no different than having your keyboard, monitor, and mouse connected directly to the computer. All functions, applications, upgrades and other items can be done normally. The only difference is the computer can be up to 33,000 feet away (6,500 feet using the 3.2 GBit model) Local access on the CrystalView DVI Fiber allows an additional KVM station to be connected to the transmitter.
TROUBLESHOOTING Troubleshooting The troubleshooting section is used as a guide to understanding the capabilities of the CrystalView DVI Fiber and for general troubleshooting. If you have any problems or questions concerning the installation, operation or usage of the CrystalView DVI Fiber that is not covered in this manual, please contact Rose Electronics for technical support. There isn’t a picture. • Check the power supply connection at the Local unit.
SERVICE AND SUPPORT Service Information Maintenance and Repair This Unit does not contain any internal user-serviceable parts. In the event a Unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repair center. This Return Authorization number must appear on the outside of the shipping container. See Limited Warranty for more information.
SAFETY Safety The CrystalView DVI Fiber KVM extender has been tested for conformance to safety regulations and requirements, and has been certified for international use. Like all electronic equipment, the CrystalView DVI Fiber should be used with care. To protect yourself from possible injury and to minimize the risk of damage to the Unit, read and follow these safety instructions. 12 Follow all instructions and warnings marked on this Unit.
Safety and EMC Regulatory Statements Safety information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. CAUTION A CAUTION in the manual denotes a hazard that can damage equipment. Do not proceed beyond a WARNING or CAUTION notice until you have understood the hazardous conditions and have taken appropriate steps.
APPENDICES Appendix A. General specifications Maximum resolution 1920 x 1200 @ 60Hz Video compatibility DVI-D Keyboard PS/2 or USB Mouse PS/2 or USB Power adapter 90-240 VAC adapter to 5VDC / app. 10W Transmitter power 750 mA Receiver power 750 mA Connectors Video to PC – DVI-D Video to KVM – DVI-D Keyboard: PS/2 or USB Mouse: PS/2 or USB Interconnect: Fiber type LC Fiber cable length 62,5µm Multimode-Fiber 650 ft / 200m 50.0µm Multimode-Fiber 1300ft / 400m 9.
APPENDICES Appendix B.
10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.
