Rackview 20” – KVM Rack Drawer INSTALLATION AND OPERATIONS MANUAL Rackview 20” LCD KVM Rack Drawer 1600 x 1200 Rose Electronics 10707 Stancliff Road Houston, Texas 77099 Phone (281) 9337673 WWW.ROSE.
LIMITED WARRANTY LIMITED WARRA Rose Electronics warrants the Rackview Product to be in good working order for one year from the date of purchase from Rose Electronics. Should this product fail to be in good working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All replaced parts become the property of Rose Electronics.
Rose Electronics Part # MAN-RV1-CSKVT20 Printed In the United States of America – Revision 1.0 Table of Contents Safety Instructions Page 4 Pre-Installation and Package Contents Page 5 Layout Diagram and Dimensions Page 6 Installation Procedure Page 7-9 OSD Function and Front Panel Controls Page 10-12 Cable Connections Page 12 Configuring Display Settings Page 12 Specifications Page 14 Technical Support Page 15 Page 3 KVM Rack Drawer 20” WWW.ROSE.
Safety Instructions Please read all of these instructions carefully before you use the device. Save this manual for future reference. • Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth. • Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with temperatures not exceeding 50º Celsius (104º Fahrenheit).
Pre-Installation and Package Contents Before Installation: It is very important to mount the equipment in a suitable cabinet or on a stable surface. Make sure the mounting location has good ventilation, is out of direct sunlight, and away from sources of excessive dust, dirt, heat, water, moisture and vibration. Unpacking: The equipment comes with the standard parts shown in package content. Check and make sure they are included and in good condition.
Rackview Layout Diagram & Dimensions Model Product Dimension (W x D x H) approx Packing Dimension (W x D x H) approx RV1-CSKVT20/DVI 526 x 436.4 x 43.8 mm 20.8 x 17.2 x 1.7 inch 827 x 564 x 206 mm 32.6 x 22.2 x 8.1 inch Page 6 KVM Rack Drawer 20” Net Weight 16.5 kg 36.4 lb Gross Weight 22.5 kg 49.6 lb WWW.ROSE.
Installation Procedure 1.1 Hardware Kit Contents 1. Rail with front and rear bracket x 2 2. Screws (length = 6mm) x 6 3. Keys x 2 1.2 Console Installation Steps 1. Adjust the rail until 2 screws appear. Loose (but don’t release) the two rear screws then adjust the depth of the rear bracket to fit your cabinet. Page 7 KVM Rack Drawer 20” WWW.ROSE.
2. Install Front and Rear brackets on the cabinet. 3. Tighten-up the two rear screws (see below) 4. Repeat steps 1-3 for the other side. 5. Pull the rails (Part A), both sides until they lock until it lock. Then take the Rackview and slide it onto the (Part A) rails, both sides. Make sure the rear connector box is secure. Page 8 KVM Rack Drawer 20” WWW.ROSE.
6. Pull the rail-release switch (left and right sides at the same time) then push the console back into the rack 7. Install three screws in the rear of the console (both sides). 8. Finish installation as below. Page 9 KVM Rack Drawer 20” WWW.ROSE.
OSD Function and Front Panel Controls Figure 1: OSD Panel Control Buttons Navigating the OSD Menu There are eight different selectable menu items in the OSD. To operate the OSD, press the “Menu” button Use the “Down” and “Up” buttons to scroll through the Menu Once the menu item has been selected, press the “Menu” button again to enter the sub-menu • Auto tune. • Input Source • Brightness • Contrast • Color • Position • Language • Recall • Exit Auto Tune Press the “auto tune” button.
Brightness Press the “menu” button to enter. Use the “Down” and “Up” button to adjust the brightness of the display. Press the “menu” button to enter. Contrast Press the “menu” button to enter. Use the “Down” and “Up” button to adjust the contrast of the display. Press the “menu” button to enter. Color Press the “menu” button to enter, and you will see Ic on Use the “Down” and “Up” button to adjust the color of the display. Press “menu” to enter.
Recall Press the “menu” button to enter, and you will see: Yes/ No Select “Yes” button then ‘Menu” button to recall the factory setting. Select “No “ to return to the previous page. Exit Press the “exit” button to quit OSD menu. Power Indicator • GREEN ON • RED STANDBY • RED SUSPEND • RED OFF Rear Panel Cable Connections Depending on which Rackview model you have purchased, the rear panel layout could look like this.
Most video cards use the Windows Display Properties control panel to configure the display. To open the Windows Display Properties, click the right mouse button in a blank area of the Windows desktop and then select Properties. The Settings tab usually lets you change the Color Palette and the Desktop Area (x by y pixel resolution). Some video cards integrate additional features into the Windows Display Properties control panel to give you an exceptional setup that is flexible and easy to use.
Rackview 20” - LCD / Keyboard / Mouse Specification Item Description 20.1" TFT color LCD Diagonal Size 1600 x 1200 (UXGA) Max. Resolution 300 Brightness (cd/m²) 16.7 M, 8-bit Color Support 700:1 Contrast Ratio (typ.) Viewing Angle (CR > 10) Right – Left 178˚ Up-Down 178˚ 0.255 x 0.
Technical Support If you are experiencing problems, or need assistance in setting up, configuring or operating your product, consult the appropriate sections of this manual. If, however, you require additional information or assistance, please contact the Rose Electronics Technical Support Department at: Phone: (281) 933-7673 E-Mail: techsupport@rose.com Web: www.rose.com Technical Support hours are from: 8:00 am to 6:00 pm CST (USA), Monday through Friday.
Rose Electronics 10707 Stancliff Road Houston, Texas 77099 © Copyright 2013 Rose Electronics. All rights reserved. Specifications subject to change without notice Page 16 KVM Rack Drawer 20” WWW.ROSE.