UltraVista LC II HDMI 2x2 HDMI Video Controller/Splitter INSTALLATION AND OPERATIONS MANUAL VWL-B122/FH 10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.
LIMITED WARRANTY Rose Electronics warrants the UltraVista LC II HDMI to be in good working order for one year from the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All replaced parts become the property of Rose Electronics.
HAZARDOUS MATERIAL DISCLOSURE The details provided below are to ensure that the product is compliant with the Peoples Republic of China RoHS standards. The table below acknowledges the presence of small quantities of certain materials in the product, and is applicable to China RoHS only.
TABLE of CONTENTS Contents Page # Disclaimer ...................................................................................................... 2 System Introduction ....................................................................................... 2 Features ..................................................................................................... 3 Package Contents ...................................................................................... 3 Rose Electronics Web Site .......
Figures Page # Figure 1. UltraVista LC II HDMI VWL-B122/FH ............................................. 5 Figure 2. Front Panel Controls ...................................................................... 6 Figure 3. Rear Panel Controls ....................................................................... 7 Figure 4. 2 x 2 Installation.............................................................................. 9 Figure 5. Bezel Calculation for VWL-B122/FH ............................................
INTRODUCTION Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein. The manufacturer reserves the right to change the specifications, functions, or circuitry of the product without notice.
Features Supports HDMI video input HDMI video outputs 2x2 Models: 1 single-link HDMI input / 4 single-link HDMI outputs Supports video input resolutions up to 1920 x 1200 Output resolutions up to 1920 x 1200 Easy adjustments for bezel compensation Expand a 2x2 model easily to a 4x4 display array Adjustments and control can be performed using a remote control or serial commands from a connected computer Compatible with most monitors that support HDMI input.
Rose Electronics Web Site Visit our web site at www.rose.com for additional information on UltraVista LC II HDMI and other products offered by Rose Electronics that are designed for data center applications, classroom environments, and many other access and switching applications. Product Registration Take advantage of the following when you register your Rose Electronics products online at http://www.rose.com/htm/online-registrationform.htm: Rose Standard Warranty Plus...
MODELS System Overview The UltraVista LC II HDMI system will take a single high-resolution digital video input and split it correctly over the output display array. The UltraVista LC II HDMI can be controlled from the built-in On Screen Display, a computer connected directly to the RS232 port on the unit, or by using the included remote control. Figure 1 shows the front and rear of the unit; the functions of the buttons and connectors on the front and rear panels are outlined in Figures 2 and 3. Figure 1.
Front Panel Indicators / Controls Video Out Indicators LEDs indicate which DVI output port has a video signal. OSD menu controls (See OSD section for Menu and menu selections) Video In Indicator LED indicates a valid input video signal is present Power Indicator LED indicates that power is applied to the unit Menu Select and Enter button When OSD is not displayed, displays the OSD, selects items and sets new item values. When OSD is displayed, selects the highlighted selection.
Rear Panel Connectors Figure 3.
INSTALLATION UltraVista LC II HDMI Installation Installation of the UltraVista LC II HDMI is an easy process, and consists of the following: Install the display panels Mount, if necessary, the video wall controller Connect HDMI cables, video input cable and power adapter to the video wall controller Adjust the screen resolution output settings Select a screen mode to display output Adjust the video wall mask settings to align images The unit can be set up to display three modes.
Installing the LCD Displays Mount the monitors as shown in figure 4. All displays should be identical in size and resolution capabilities. When mounting the displays, keep the horizontal and vertical gaps between displays consistent. 1 2 3 4 Figure 4. 2 x 2 Installation Bezel Compensation Value Calculation When all the displays have been mounted, measure the bezel width and height, and the viewable width and height as shown in figure 5.
Figure 5.
Mounting the UltraVista LC II HDMI unit The UltraVista LC II HDMI unit can be placed on a desk, or mounted on a horizontal or vertical surface using the included mounting brackets. To mount the unit using the mounting brackets, remove the four rubber feet and secure the mounting brackets to the unit using the same holes and screws as shown below. Figure 6. Mounting Brackets The installation location must meet the following conditions.
OPERATION Using the Built-In OSD features To invoke the built-in OSD, press the MENU/ENTER button on the front panel. The OSD will display on the monitor connected to the DVI output port #1. (Note: All cable connections and power must be applied.) OSD Buttons There are several On Screen Display (OSD) control buttons located on the right side of the front panel. The figure below shows the arrangement of OSD controls. Menu/ Enter Up Down Left Right Exit Figure 7.
OSD Menu Structure Menu Options / Submenu Display Output Resolution Options Display Mode Mask Control -> Horizontal % Vertical % Mask Control System Factory Reset Information Miscellaneous-> OSD Configuration Brightness Contrast Identify Monitors Table 2.
Display Menu Figure 8 shows the Display menu options, which are described below. Figure 8. Display Menu Output Resolution The Output Resolution setting shows the resolution of the video image output. The display output resolution setting options are shown below. 720p 1080p Display Mode The display mode configures how the image is displayed on the screen. The display modes are outlined in Table 3.
1x1 This is the default mode. The video input is cloned on all the monitors. 2x1 The video input is shown on the top two panels and repeated on the bottom two. 2x2 The video input is tiled over all the panels. Mode 1 Same as 2 x 2, but the top left panel shows the full image. Mode 2 Same as 2 x 2, but the top right panel shows the full image. Mode 3 Same as 2 x 2, but the bottom left panel shows the full image. Mode 4 Same as 2 x 2, but the bottom right panel shows the full image. Table 3.
Mask Control The mask control compensates for the spaces between monitors and bezel width in the video wall array. The mask control menu (Figure 9) allows for adjustment of the mask. The mask control options are shown and described below. Figure 9. Mask Control menu Horizontal Mask Sets the horizontal mask according to the formulas shown in Figure 5. Vertical Mask Sets the vertical mask according to the formulas shown in Figure 5. Mask Control The Mask Control option turns the Mask Control On or Off.
System Menu The System Menu options are shown in Figure 10 and described in subsections below. Figure 10. System Menu Factory Reset Factory Reset returns all the settings to the factory default settings. Information Shows video wall controller version information. The information details are shown in the next section. Misc. Misc. allows OSD features to be adjusted. These settings are shown in the Miscellaneous section below.
Information The information screen, shown in Figure 11, displays some basic information about the video wall controller and monitors. Figure 11.
Miscellaneous The Miscellaneous menu, shown in Figure 12, provides the option to go to the OSD setup menu. Figure 12. Miscellaneous Menu OSD Configuration Adjusts the rotation of the OSD display and the length of the inactivity period before the OSD display closes. Brightness Adjusts the display brightness. Contrast Adjusts the display contrast.
Remote controller All UltraVista LC II HDMI models are supplied with a remote control. The remote control provides the same functions as the front panel push-buttons. Power: Turns the UltraVista LC II HDMI unit On or Off.
TROUBLESHOOTING Troubleshooting on the UltraVista LC II HDMI No Image On One Monitor If there is no image on one monitor, follow these steps to fix the problem. Check monitor power Step 1: Check that the monitor is turned on. Step 2: Check that the power source for the monitor is turned on. Step 3: Check that the power source has the correct power rating (check panel specifications for details). Step 4: Make sure that the LCD panel power cables are securely fastened to the monitor and to the power source.
SAFETY Safety The UltraVista LC II HDMI has been tested for conformance to safety regulations and requirements, and has been certified for international use. Like all electronic equipment, the UltraVista LC II HDMI should be used with care. To protect yourself from possible injury and to minimize the risk of damage to the Unit, read and follow these safety instructions. Follow all instructions and warnings marked on this Unit.
SERVICE Service Information Maintenance and Repair This Unit does not contain any internal user-serviceable parts. In the event a Unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repair center. This Return Authorization number must appear on the outside of the shipping container. See Limited Warranty for more information.
APPENDICES Appendix A – General Specifications Specification Detail Model Name VWL-B122/FH Main Features 1. Multiple Viewing Modes 2. Software OSD 3. Remote Control 4. Bezel masking Inputs 1 x HDMI Outputs 4 x HDMI Dimensions (W x D x H) 6.14 in x 6.65 in x 2.
10707 Stancliff Road Houston, Texas 77099 Phone (281) 933-7673 www.rose.