VIDEO SPLITTER DVI INSTALLATION AND OPERATIONS MANUAL 10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.
LIMITED WARRANTY Rose Electronics® warrants the VideoSplitter DVI to be in good working order for one year from the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All replaced parts become the property of Rose Electronics.
TABLE of CONTENTS Contents Page # Disclaimer .........................................................................................................1 System Introduction ..........................................................................................1 Features ........................................................................................................2 Compatibility ..................................................................................................
INTRODUCTION Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein. The manufacturer reserves the right to change the specifications, functions, or circuitry of the product without notice.
Features 1 x 2, 1 x 4, and 1 x 8 models available Single-link DVI video support Standard DVI-I connections Supports digital or analog video (adapter required for analog video) Video resolutions: Up to 1920 x 1200 @ 60Hz Easy to install, no configuration needed Compatible with DVI standard by DDWG DVI video output #1 is used for the main display. The other outputs follow output #1.
MODELS Video Splitter DVI Models Model Connectors DVI-IN (1) - DVI-I DVI-OUT (2) - DVI-I VSP-2DVI ( Rear View) DVI-IN (1) - DVI-I DVI-OUT (4) - DVI-I VSP-4DVI (Rear View) DVI-IN (1) - DVI-I DVI-OUT (8) - DVI-I VSP-8DVI (Rear View) Figure 1. Models Cables The only cable needed is a DVI-I MM cable to connect the unit with a PC or Set-Top Box. DVI monitors connect directly to the DVI-I F connectors on the rear panel.
INSTALLATION Installation Installing the Video Splitter DVI is a very simple and straight forward process. It is recommended that all equipment be powered off to start. Connect your DVI or VGA video source (PC, Set-Top Box, DVD Player, etc) to the DVI-IN connector (DVI-I Female) on the rear panel. If you are using a VGA video source, a VGA to DVI adapter must be used. Next connect your DVI video monitor cables to the DVI-I connectors on the rear panel labeled Output x.
If your application requires that the DVI monitors be extended further than the standard 15 to 32 feet that a DVI cable allows, Rose Electronics offers a CATx and a Fiber DVI extender unit that can extend the distance up to 450 feet using CATx cable or up to 6 miles using singlemode fiber cable. DVI Video cable CATx or Fiber cable Video Splitter DVI DVI Transmitters DVI Receivers Figure 3. Extended Distance Installation Sytem Operation The operation of Video Splitter DVI is very easy and simple.
TROUBLESHOOTING Troubleshooting The troubleshooting section is used as a guide to understanding the capabilities of the Video Splitter DVI and for general troubleshooting. If you have any problems or questions concerning the installation, operation or usage of the Video Splitter DVI that is not covered in this manual, please contact Rose Electronics for technical support.
SERVICE and SUPPORT Service Information Maintenance and Repair This Unit does not contain any internal user-serviceable parts. In the event a Unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repair center. This Return Authorization number must appear on the outside of the shipping container. See Limited Warranty for more information.
SAFETY Safety The Video Splitter DVI has been tested for conformance to safety regulations and requirements, and has been certified for international use. Like all electronic equipment, the Video Splitter DVI should be used with care. To protect yourself from possible injury and to minimize the risk of damage to the Unit, read and follow these safety instructions. Follow all instructions and warnings marked on this Unit. Except where explained in this manual, do not attempt to service this Unit yourself.
Safety Safety information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. CAUTION A CAUTION in the manual denotes a hazard that can damage equipment. Do not proceed beyond a WARNING or CAUTION notice until you have understood the hazardous conditions and have taken appropriate steps.
APPENDICES Appendix A – General Specifications Resolution 1920 x 1200 (PC) Video Bandwidth 165 MHz (VGA – UXGA), Single Link Connectors DVI-I Input / Output DVI Channels 1 input / 2, 4, or 8 Output channels Max cable length 32.8 feet (10M) Power 110-220V 60Hz to 5VDC Operating Temperature 32°F - 122°F ( 0°C - 50°C) Storage Temperature 14°F - 150°F (-10°C - 70°) Humidity 30% to 80% non condensing Dimensions (2 port model) 7.93”W x 3.75”D x 1.
10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.