Caution : You must read this before you proceed Single Chair Label Description QTY A Left Armrest 1 B Right Armrest 1 C Sofa Seat 1 D Sofa Back 1 Description QTY E Bolt M6*40mm 12 F washer rings 12 G Allen Key 1 Label Picture Picture Page 1 of 5
Before Beginning Assembly: Overview Sofa Back (D) Right Armrest (B) Left Armrest (A) Sofa Seat (C) This Sofa has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Sofa parts, the above picture is to help you put the various parts into perspective. Please read through the instructions here below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean and soft surface. Unpack all packages of hardware. Place the Backrest(D) to Right Armrest(B),make the metal rod on the Backrest(D) insert into the mounting position :Position#1 . Attach Backrest(D) and Right Armrest(B) together with hardware at :Positions#2 . Use an Allen Key(G) to partially tighten these. DO NOT FULLY TIGHTEN THE BOLTS. ATTENTION: There may be some PE wicker that may have covered the bolt points.
Step 3 Repeat Step1&Step 2 to fix up Left Armrest(A) by turn show as the picture from position#8 to position#12 with hardware. Use an Allen Key(G) to partially tighten these. Tighten all Bolts completely. Step 4 Turn the Single Chair right side up. Place the Single Chair on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and gracefully, sit into to the Sing Chair. This would help to align all the parts at all the joint areas.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Love Seat Label Description QTY A Left Armrest 1 B Right Armrest 1 C Sofa Seat 1 D Sofa Back 1 Description QTY E Bolt M6*40mm 13 F washer rings 13 G Allen Key 1 Label Picture Picture Page 1 OF 5
Before Beginning Assembly: Overview Sofa Back (D) Left Armrest (A) Right Armrest (B) Sofa Seat (C) This Love Seat has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Love Seat parts, the above picture is to help you put the various parts into perspective. Please read through the instructions here below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean and soft surface. Unpack all packages of hardware. Place the Backrest(D) to Right Armrest(B),make the metal rod on the Backrest(D) insert into the mounting position : Position#1 . Attach Backrest(D) and Right Armrest(B) together with hardware at : Positions#2 . Use an Allen Key(G) to partially tighten these. DO NOT FULLY TIGHTEN THE BOLTS. ATTENTION: There may be some PE wicker that may have covered the bolt points.
Step 3 Repeat Step1&Step 2 to fix up Left Armrest(A) by turn show as the picture from position#9 to position#13 with hardware. Use an Allen Key(G) to partially tighten these. Tighten all Bolts completely. Step 4 Turn the Loveseat right side up. Place the Loveseat on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and gracefully, sit into to the Loveseat. This would help to align all the parts at all the joint areas.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Table Label Description QTY A Table Top 1 B Middle Shelf 1 C Left leg 1 D Right leg 1 E Support Bar 1 Description QTY F Bolt (M6*20) 5 G Bolt (M6*35) 9 H washer rings 13 J Allen Key 1 Label Picture Picture Page 1 OF 5
Before Beginning Assembly: Over View Table Top(A) Right leg(D) Left leg(C) Middle Shelf(B) This Table has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions here below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean and soft surface. Unpack all packages of hardware. Place the Table top(A) with its inner side, facing skywards . Put the Left leg(C) against the Table top(A),Attach Left leg(C) and Table top(A) together with hardware at position#1. Use an Allen Key(J) to partially tighten these. DO NOT FULLY TIGHTEN THE BOLTS. Step 2 Put the Right leg(D) against the Table top(A), Attach Right leg(D) and Table top(A) together with hardware at position#2.
Step 4 another hand to support Attach Support Bar(E) between Left leg and Right Leg using the hardware to fix the position 4 show as the picture. DO NOT FULLY TIGHTEN THE BOLTS. Note: Better to fix this step by 2 person together. Step 5 Place the table on a LEVEL SURFACE to check for wobbles. If it wobbles lift the dining chair to some 30cm to 50cm height from the ground. Keep your feet and toes well away from the drop zone.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.