User manual Refrigerator RJKL4150 RJKL4150V
Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 4 5 5 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Environmental concerns _ _ _ _ _ _ _ _ _ _
Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel to avoid hazard. 1. 2. • • • • Power cord must not be lengthened. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3. Make sure that you can come to the mains plug of the appliance. 4. Do not pull the mains cable. 5.
Control panel MAX To operate the appliance, proceed as follows: • turn the Temperature regulator counter clockwise to obtain warmer storage temperature. • turn the Temperature regulator clockwise to obtain colder storage temperature. min 1 2 1 Fridge temperature regulator 2 Fridge OFF position Switching on Insert the plug into the wall socket. Turn the Fridge Temperature regulator clockwise to a medium setting.
Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be placed at different heights. Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required. Important! Do not move the big lower door shelf to ensure correct air circulation. Helpful hints and tips Hints for energy saving • Do not open the door frequently or leave it open longer than absolutely necessary.
Periodic cleaning The equipment has to be cleaned regularly: • clean the inside and accessories with lukewarm water and some neutral soap. • regularly check the door seals and wipe clean to ensure they are clean and free from debris. • rinse and dry thoroughly. Important! Do not pull, move or damage any pipes and/or cables inside the cabinet.
What to do if… During operation of the appliance some smaller but annoying trouble can often occur, which does not require calling a technician out. In the following chart information is given about them to avoid unnecessary charges on service. Important! The appliance operates discontinuously, so the stopping of compressor does not mean being no current. That is why you must not touch the electrical parts of the appliance before breaking the circuit.
Problem The temperature in the appliance is too warm. Possible cause Solution The Temperature regulator may be set incorrectly. Set a colder temperature. The door is not closed correctly. Refer to "Closing the door". The food temperature is too warm. Let the food temperature decrease to room temperature before storage. The temperature in the refrig- There is no cold air circulation in the eration is too warm. appliance. Make sure that there is cold air circulation in the appliance.
Technical data RJKL4150 RJKL4150V Dimension Height 1850 mm 1850 mm Width 595 mm 595 mm Depth 623 mm 623 mm Voltage 230 V 230 V Frequency 50 Hz 50 Hz The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. Installation Caution! Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.
Removing the transport support Your appliance is equipped with transport support to secure the door during transportation. To remove them do these steps: 1. 2. 3. Open the door. Remove the transport support from the door sides. Remove the transport support from the lower hinge (some models). • Remove the ventilation grille. Remove the filling and install it on the opposite side of the grille. • Lay down the appliance back side down on a wooden support.
• Unscrew the handle. On the opposite side remove the hole covers by driving a 3-4 mm drift or drill into them. Install the handle. Install the hole covers provided within the accessory bag. • Put the cabinet in position. Warning! Reposition, level the appliance, wait for at least four hours and then connect it to the power socket. Do a final check to make sure that: • All screws are tightened. • The edges of the doors run parallel to the side edge of the appliance.
www.electrolux.
