User manual Freezer RPP3250
Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 6 6 7 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _
Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel to avoid hazard. 1. 2. • • • • Power cord must not be lengthened. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3. Make sure that you can come to the mains plug of the appliance. 4. Do not pull the mains cable. 5.
• This product must be serviced by an authorized Service Centre, and only genuine spare parts must be used. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local authorities.
1. 2. 3. Press the ON/OFF button for a few seconds. The display switches off. To disconnect the appliance from the power disconnect the mains plug from the power socket. Temperature regulation The set temperature of the freezer may be adjusted by pressing the temperature regulators. Set default temperature: • -18°C for the freezer The temperature indicators show the set temperature. The set temperature will be reached within 24 hours. Important! After a power failure the set temperature remains stored.
Important! The function switches off by selecting a different freezer set temperature. High temperature alarm Temperature increase in the freezer compartment (for example due to an earlier power failure or door is open) is indicated by: • flashing the alarm and freezer temperature indicators • sounding of buzzer. To reset the alarm: 1. Press any button. 2. The buzzer switches off. 3. The freezer temperature indicator shows the highest temperature reached for a few seconds.
1 2 Helpful hints and tips Hints for freezing To help you make the most of the freezing process, here are some important hints: • the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate; • the freezing process takes 24 hours.
Clean the condenser (black grill) and the compressor at the back of the appliance with a brush. This operation will improve the performance of the appliance and save energy consumption. Important! Take care of not to damage the cooling system. Important! When moving the cabinet, lift it by the front edge to avoid scratching the floor. Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the plastics used in this appliance.
Problem Possible cause Solution The buzzer sounds. The Alarm icon flashing. The temperature in the freezer is too high. Refer to "High Temperature Alarm". upper or lower square is shown in the temperature display. An error has occurred in measuring the temperature. Call your service representative (the cooling system will continue to keep food products cold, but temperature adjustment will not be possible). The compressor runs continuously. The Temperature regulator may be set incorrectly.
As much as the advice does not lead to result, call the nearest brand-mark service. Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Service Center.
the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician. The manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with the E.E.C. Directives. Removing the transport support Your appliance is equipped with transport support to secure the door during transportation. To remove them do these steps: 1. 2. 3. Open the door.
www.electrolux.
