CASE 5600 Series USER Manual www.rosewill.
User Manual CASE 5600 series Contents P.2 P.3 Configuration Features Descriptions Installation P.5 P.6 P.8 P.9 P.10 P.11 P.13 P.13 P.14 P.15 P.16 1. Opening Chassis 2. Installing Motherboard 3. Installing 3.5" HDD 4. Installing 5.25" Device 5. Installing Add on Card 6. Installing Floppy 7. Cleaning Filters-Air guide Filter 8. Cleaning Filters-Front panel Filter 9. USB port 10. IEEE1394 Port 11. Audio Port P.17 P.18 12. System Control Connectors Information 1 © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series Configuration Dimension (W x H x D) 7.9" x 17.3" x 19.4" M/B Size ATX, Micro ATX Drive Bay External : 4 x 5.25" + 2 x 3.5" Internal : 5 x 3.5" Expansion Slots Thermal Solution Air Filter I/O Port Bracket Megal Material 7 Slots 1 x 12 cm fan in rear and 1 x 12 cm fan holder in front One air filter on the front panel ( only in R6A34) Supports one I/O port bracket for standard ATX M/B 0.8 mm thickness SECC rustproof & galvanized JIS Steel 2 © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series Features Descriptions Front 120mm Fan Rear 120mm Fan Sliding Rails for 5.25" device Sliding Rails for 3.5" HDD Screw-less Add-on Card assembly Door opening up to 270 Degree Easy-clean filter (in left side panel) Easy-clean filter (in front panel) 3 © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series Screw-less and lockable left side panel Adjustable air inflow Front IO Ports 4 Convenient Accessory box © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series Installation 1.Opening Chassis 1.1 Take off the thumb screws on the back plane 1.2 Push the Key-button 1.3 Roll the side cover anticlockwise to open 5 1.4 Push hooks marked in red circle to detach the front panel from the chasis © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 2.Installing Motherboard ATX Motherboard Special motherboard stand-off 2.2 Sit the motherboard on our special motherboard stand-off and screw in all the screws into the motherboard stand-offs. 2.1 Due to our special design of motherboard stand-off,copper motherboard stand-off not needed when you install the ATX motherboard. NOTE : The copper motherboard stand-off not needed when you install the ATX motherboard.
User Manual CASE 5600 series Micro ATX Motherboard 2.1 Locate and align the screw holes on the motherboard and chasis; place the motherboard at the correct position, and then screw copper motherboard standoffs brass studs onto chassis's metal shell. 2.2 Sit the motherboard on themotherboar stand-offs and screw in all the screws into the motherboard stand-offs. Note: Screw holes marked with "M" are motherboard stand-off positions for micro ATX motherboard. 7 © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 3.Installing 3.5" HDD 3.1 Insert the screw into the rubber pad hole on the rail 3.2 Attach rails to bothe sides of your HDD 3.3 Insert the railed HDD into the 3.25" HDD bay and push to the buttom NOTE : Screws for HDD have no thread, no screwdriver needed when you work step 3.2 8 © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 4.Installing 5.25" Device 4.1 Disassemble the front panel (please refer to step 1.4 ) 4.2 Attach rails to both sides of your 5.25" device PS: You can also fasten rails on your 5.25" device by screws 4.3 Insert the railed 5.25" device into the 5.25" drive bay 9 © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 5.Installing Add on Card 5.1 Push out to loosen add on card kit 5.2 Insert your add on card into the right slot 10 5.3 Push down add on card kit to fasten the add on card © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 6.Installing Floppy 6.1 Detach the front panel (Please refer to Step 1.4, Page 5) 6.2 Unscrew the screws holding the floppy cage 6.3 Slide out the floppy cage 11 6.4 Remove the metal cover © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 6.5 Secure the floppy on cage by screws 6.6 Slide the floppy cage back 6.7 Secure the floppy cage by screws 12 6.8 Attach the front panel © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 7.Cleaning Filters - Air Guide Filter 8.Cleaning Filters - Front panel Filter 7.1 Turn anticlockwise to take off the filter 8.1 Push front panel hooks to detach the front panel from the chassis ( please refer to step 1.4 ) 13 8.2 Detach the filter from the front panel © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 9.USB Port NOTE : 1.Make sure that your motherboard offers USB interface. NOT every motherboard offers it. 2.NEVER connect a IEEE1394 connector to the USB pins. It will damage the motherboard. 9.1 Read your motherboard’s user manual to find the pins for the USB connector. 9.2 Find the USB connector and connect it to the pins. M/B USB PINS USB+5V USB_P5 USB_P5 + GND 14 USB+5V USB_P8 USB_P8 + GND ON © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 10.IEEE1394 Port NOTE : 1.Make sure that your motherboard offers IEEE1394 interface. NOT every motherboard offers it. 2.NEVER connect a USB cable to the IEEE1394 connectors. It will damage the motherboard. 10.1 Read your motherboard’s user manual to find the pins for the IEEE1394 connector. 10.2 Find the IEEE1394 connector and connect it to the pins. M/B IEEE1394 PINS TPA2+ GND TPB2+ +12V 15 GND +12V TPB2 GND TPA2 © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 11.Audio Port NOTE : Make sure that your motherboard offers Audio interface for front panel. NOT every motherboard offers it. 10.1 Read your motherboard’s user manual to find the pins for the Audio connector. 10.2 Find the Audio connector and connect it to the pins. M/B Audio PINS MIC2 MICPWR Line out_R AGND +5VA Bline_out_R NC Line out_L 16 Bline_out_L © 2004-2006 Rosewill Inc.
User Manual CASE 5600 series 12.System Control Connectors 1. Read your motherboard’s user manual to find the pins for these system control connectors. 2. Refer to your motherboard’s user manual to connect these connectors correctly. Connectors System Warning Speaker +5V Ground Ground Speaker Reset Ground PLED- IDE_LED System Power LED SPEAKER PWA Ground Reset Switch IDE_LED+ IDE_LED- ATX Power Switch PLED+ PLED ATTENTION : The diagram is just an example.
User Manual CASE 5600 series Thank you for purchasing a High-Quality Rosewill Product. Please register your product at : www.rosewill.com for complete warranty information and future support for your product. If you have any question while using our products, please visit our website : www.rosewill.com for latest driver & user manual or feel free to contact us at feedback@rosewill.com Support Phone Number: 800-575-9885 Support Email: techsupport@rosewill.com 18 © 2004-2006 Rosewill Inc.
www.rosewill.
