LCD TV R908TV R918TV User Manual
LCD TV R908TV R918TV User Manual Chapter 1 Introduction This chapter provides basic information about your LCD TV.
LCD TV R908TV R918TV User Manual Warnings and precautions • • • • • • • • • • Do not place your hands, face, or objects close to the ventilation openings of you LCD TV. The top of your LCD TV gets very hot from exhaust air that is released through the ventilation openings. Burns or personal injuries may occur if you are too close the LCD TV. Damage may occur if you place any object near the top of your LCD TV. Disconnect all cables before moving you LCD TV.
LCD TV R908TV R918TV User Manual A.
LCD TV R908TV R918TV User Manual B.
User Manual LCD TV R908TV R918TV C. OSD (On Screen Display) menu enables user to manipulate the image and settings OSD Main menu consists of source: 1. COLOUR 2. PICTURE 3. OSD MENU 4. MISCELLANEOUS 5.
User Manual LCD TV R908TV R918TV PICTURE H. Position V.
LCD TV R908TV R918TV User Manual OSD MENU Language OSD H. Position OSD V.
User Manual LCD TV R908TV R918TV EXIT Exit Press “MENU“ to go back MENU VIDEO OSD Contrast Press “+” “-“ or IR to adjust image get distinct or vague Brightness Press “+” “-“ or IR to adjust image get dark or bright Hue Press “+” “-“ or IR to adjust screen deflection red of green Saturation Press “+” “-“ or IR to set favorite saturation color Press “MENU“ to go back MENU Exit 8
User Manual LCD TV R908TV R918TV TV OSD TV Signal TV System CH Auto Scan CH Edit Exit Press “+” “-“ or IR to select TV signal from CATV or AIR Press “MENU” into TV system to select NTSC,NTSC-J or PAL system Press “+” “-“ or IR to select channel Press “+” “-“ or IR to chose Auto search channel Press “MENU” into CH Edit Press “MENU“ to go back MENU 9
LCD TV R908TV R918TV User Manual TV System Press “MENU” into TV system Press “UP “DOWN“ or IR to change the TV system (NTSC, PAL) Select “Exit” and press “Menu” to exit TV Sstem CH Edit Press “MENU” into CH Edit 10
LCD TV R908TV R918TV User Manual CUR CHANNEL: Press remote control number key, enter channel number. Then press IR MENU key jump to NEW CHANNEL. Press IR key cancel channel number to zero. NEW CHANNEL: Press remote control number key and you want change channel number. Then press IR MENU key. Press IR key cancel channel number to zero. Press IR MENU KEY save channel ,then current channel and new channel swap. Press IR key cancel your setting and recall default program table.
LCD TV R908TV R918TV User Manual D.
LCD TV R908TV R918TV User Manual 13
LCD TV R908TV R918TV User Manual 14
LCD TV R908TV R918TV User Manual 15
LCD TV R908TV R918TV User Manual 16
LCD TV R908TV R918TV User Manual E. Applicable Timing This A/D board supports the video timing listed above. In some cases, TFT LCD manufacturers guarantee within specific pixel frequency (dot clock) Range based on the application range. As example, TFT LCD hardly displays the Image properly over 60Hz refresh rate. And also TFT LCD has the best performance at 60 Hz refresh rate. Therefore, it is highly recommended for customers to use this product at 60 Hz refresh rate.
User Manual LCD TV R908TV R918TV PC RGB Input Input Signal Input Impedance Polarity Amplitude Multi-mode Supported Analog RGB 0.7Vp-p 75 Ohm ± 2% Positive, Negative 0 ~0.7 ± 0.05Vp Hhorizontal Frequency: 30~60KHz Vertical Frequency: 50~75Hz Power Supply Input Voltage Output Voltage Power Management 100~240VAC, 50/60Hz +12V DC, 4.2A (50W) On: 50W max. (Green LED) Off: 1W max.
LCD TV R908TV R918TV User Manual Chapter 6 Safety, Regulatory and Legal Information US Regulatory compliance statements Your LCD TV has been tested and found to comply with the limits for a Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.