8 Ports Green Fast Ethernet PoE Metal Switch RFS-108P User Manual
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of Rosewill Inc. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Rosewill Inc. Copyright © 2010 Rosewill Inc. All rights reserved. http://www.rosewill.
CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Safety Warning Place connecting cables carefully so that no one will step on them or stumble over them. Always disconnect all cables from this device before servicing or disassembling. Use ONLY an appropriate power adaptor or cord for your device.
Package Contents The following contents should be found in your package: One RFS-108P Switch One power cord This User Guide Racket-mount brackets Wall-mount kit Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.
IEEE 802.3af Power over Ethernet (PoE) Standard Compliant: - Up to 15.4 watts maximum per Port (Port 1~4); - Supports PoE Over Current Protection; - Supports PoE Circuit Shorting Protection - Supports PoE Powered Device(PD) classification identify allows to detect power range Complies with 10BASE-T specifications of the IEEE802.3 standard Complies with 100BASE-TX specifications of the IEEE802.3u standard Push on/off button to enable/disable IEEE802.3az Compliant with IEEE 802.
LEDs Definition The switch contain 1x Power LED for the device, 1x 10/100M LED for each port and 1x PoE LED for port 1 ~ port 4. LED Power Link/ ACT Status Operation Steady Green Off 10M: Green 100M: Amber Blinking 10M: Green 100M: Amber Off The switch is powered on The switch is powered off Green PoE Off The port is connected Data transmitting /receiving. No valid link on this port One PoE compliant device is connecting with this port. There is no PoE compliant device connecting with this port.
Power Receptacle To be compatible with the electric service standards around the world, the switch is designed to afford the power supply in the range from 100 ~ 240VAC, 50/60Hz. Please make sure that your outlet standard to be within this range. To power on the switch, plug the female end of the power cord firmly into the receptacle of the switch and the other end into an electric service outlet. After the power cord installation, please check if the power LED is illuminated for a normal power status.
horizontally. Leave a small gap between the head of the screw and the wall. The gap should be big enough for the screw heads to slide into the screw slots and the connection cables to run down the back of the switch. 2. Align the holes on the back of the switch with the screws on the wall. Hang the switch on the screws. Warning! Do not wall mount the product vertically or it will be dangerous.
5. Repeat the two previous steps for the other side of the unit. 6. Insert the unit into the rack and secure with suitable screws. 7. Reconnect all the cables. Network Cables In making a switch interconnection, you could use any port to connect another switch with straight or crossover cable. As all the ports support auto MDI / MDI-X function, using a straight cable to make a switch-to-switch connection is allowed. 1.
Media 10/100 Mbps ports Ports that support PoE (Port 1~Port4) Speed Wiring 10 Mbps Category3,4,5 UTP/STP or above. 100 Mbps Category 5 UTP/STP or above. 10/100 Mbps Category5,5e UTP/STP or above. Network Application The following picture is an application sample of network topology for your reference: Product Specifications Standard Interface Network Data Rate Transmission Mode IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3az Energy Efficient Ethernet IEEE802.
Memory Emission Safety Power Consumption Operating Temperature Operating Humidity Power Supply Appendix A: 1. 1K MAC entries 768K Bits buffer Memory CE, FCC Class A LVD 75W Max. 00 ~ 400C (320 ~ 1040F) 10% - 90%(non-condensing) Input :100-240V, 50/60MHz, 1.5A Max Output：48VDC/1.56A Troubleshooting The Power LED is not lit Make sure the AC power cord connected the Switch with power source properly. 2. Make sure the power source is ON.
