Wireless N Adapter RNX-N250UBE User Manual
Wireless N Adapter RNX-N250UBE User Manual FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
Wireless N Adapter RNX-N250UBE User Manual required Luxembourg General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Only for indoor applications Federation Note: Please don’t use the product outdoors in France.
Wireless N Adapter RNX-N250UBE User Manual Table of Content Chapter 1 Overview .........................................................................................5 Package Content ......................................................................................5 1.1 Overview of the Product.................................................................5 1.2 Features.........................................................................................6 1.3 System Requirement.................
Wireless N Adapter RNX-N250UBE User Manual Chapter 1 Overview Thank you for choosing Rosewill’s 802.11n 2T2R Wireless USB adapter – RNX-N250UBE. RNX-N250UBE is a powerful 300Mbps USB 2.0 Adapter into PCs or NB without any hassle. The Adapter can be used in Ad-Hoc mode to connect directly with other cards for peer-to-peer file sharing or in Infrastructure mode to connect with a wireless access point or router for access to the Internet in your office or home network.
Wireless N Adapter RNX-N250UBE User Manual With the 802.11n technology, higher throughput improvements using MIMO (multiple input, multiple output antennas), the RNX-N250UBE’s transfer rate up to 300Mbps for maximum throughput. It can also interoperate with other wireless (802.11b, 802.11g) products. The adapter supports 64/128-bit WEP, WPA and WPA2 encryption to prevent outside intrusion and protect your personal information from being exposed. The adapter is easy to install and manage.
Wireless N Adapter RNX-N250UBE 1.4 User Manual Specification Specifications Standard IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Interface USB 2.0 Frequency Range Wireless Transmit Power Modulation Technology 2.4-2.4835GHz 18dBm (max. EIRP) OFDM/CCK/16-QAM/64-QAM Security Support 64/128 bit WEP, WPA-PSK/WPA2-PSK Antenna 2x external detachable 5dBi Antenna Windows 2000/ XP/ Vista/ 7 (32/64bit), Linux Kernel 2.6.x, and MAC System Support OSX 10.4, 10.5, 10.6, 10.
Wireless N Adapter RNX-N250UBE User Manual Chapter 2 Installation Guide 2.1 z z Software Installation Insert the Driver and Utility CD-ROM into the CD-ROM driver. The Wizard should run automatically, and below window should appear. If not, click the Start button and choose Run. In the field that appears, enter D:\autorun.exe (if ‘’D’’ is the letter of your CD-ROM drive). Next we use the USB wireless adapter installation steps as example.
Wireless N Adapter RNX-N250UBE User Manual z Click Next z Click Install to start installing z Follow the InstallShield Wizard steps, and click Finish when done.
Wireless N Adapter RNX-N250UBE z User Manual Now your PC or notebook will restart automatically.
Wireless N Adapter RNX-N250UBE User Manual Chapter 3 Wireless Connection Guide This chapter describes how to configure your Adapter for wireless connectivity on your Wireless Local Area Network (WLAN) and use the data security encryption features. After Installing the Adapter, the Adapter’s tray icon will appear in your system tray. It appears at the bottom of the screen, and shows the signal strength using color and the received signal strength indication (RSSI).
Wireless N Adapter RNX-N250UBE User Manual 3.2. Connecting with Window 7 You can easily access to wireless with Win7. First, move your mouse to lower right hand corner as below and click on the icon where arrow pointing to. Click Refresh to get an update of your Wireless Network Connection. This should help you search the SSID of the network you want to connect to. Select your desired SSID, then Click “Connect”.
Wireless N Adapter RNX-N250UBE User Manual You will be prompt to ask you entering the network security key. Once entered, please click OK to complete. You should see below in a very short period and find out whether you are connected or now. 3.3. Connecting with Wireless LAN Utility We provide this Utility for users to connect to a wireless network easily. It provides more information and configuration for this adapter.
Wireless N Adapter RNX-N250UBE User Manual automatically upon starting your computer and connects to a connectable wireless network with best signal strength and with no security setting. 3.3.1 Step 1: Search Available Network First Select the Available Network option: You will see a list of the SSID that your wireless adapter has scanned in your surrounding area. You can also “Refresh” to see the most updated list. 3.3.
Wireless N Adapter RNX-N250UBE User Manual After click “Add to Profile”, you will see the next window “Wireless Network Properties” popup with your current wireless signal’s setting. (RNX-N180PCe will detect the current setting of your SSID). So after the “Wireless Network Properties” popup, all you need to do is to enter the password of your SSID and click OK to continute. When done, your wireless adapter will automatically connect to this SSID.
Wireless N Adapter RNX-N250UBE User Manual Chapter 4 Utility Configuration – Win XP’s Station Mode The Wireless Adapter provides two modes: Station mode and Access Point mode, the default is Station mode under Window XP. You can select connect wirelessly to your Wireless router/AP to connect to Internet in station mode. But in the Access Point mode, the wireless adapter act as a wireless access point which can share Internet connection with others. (Access Point Mode requires Wired Connection) 4.1.
Wireless N Adapter RNX-N250UBE User Manual Network Address z MAC Address: The MAC Address of the Adapter. z IP Address: The IP Address of the Adapter. z Subnet Mask: The Subnet Mask of the Adapter. z Default Gateway: The Default Gateway address of the Adapter. Others z Show Tray Icon: Show USB Wireless LAN Utility icon in the windows taskbar notification area. z Disable Adapter: Disable the wireless adapter. z Radio off: Turn off the radio of the wireless adapter. 4.2.
Wireless N Adapter RNX-N250UBE User Manual When the Network Info dialog box appears, enter a name for the new profile. Enter the Network SSID. Choose the Network Authentication Mode and Data encryption from the drop-down menu and import the network key. Then click OK button. z Create a new ad-hoc mode profile If you want your wireless computers communicate with each other directly, click the Add button to create a new ad-hoc profile.
Wireless N Adapter RNX-N250UBE User Manual menu. And import the network key. Then click OK button. You have successfully created a profile. 4.2.2 Remove Select a profile and click Remove button to delete this profile. 4.2.3 Edit Select a profile and click Edit button to edit this profile.
Wireless N Adapter RNX-N250UBE User Manual Modify the profile information according to your demand. 4.2.
Wireless N Adapter RNX-N250UBE User Manual Import the new profile name in the popup window blank 4.2.5 Set default When you want to make one profile as a default wireless connection, you should select the profile and click Set default button. The wireless adapter will use this profile to connect to wireless network automatically when the utility running next time.
Wireless N Adapter RNX-N250UBE User Manual 4.3. Available Network The Available Network tab displays a list of infrastructure and ad-hoc networks for available wireless connection Double-click the network to which you wish to connect.
Wireless N Adapter RNX-N250UBE User Manual Choose the Authorization modes and Encryption modes in the drop-down box. If the wireless network uses a Passphrase, enter the Passphrase in the Passphrase field. If the wireless network uses a WEP key, enter the WEP key in the Key field. Click the OK button to complete the network connection. 4.4. Status The Status tab displays the detailed information of current device and wireless connection.
Wireless N Adapter RNX-N250UBE User Manual 4.5. Statistics The Statistics tab display the stat. value of current wireless connection Tx and Rx, you can click Reset button to reset value and restart to count.
Wireless N Adapter RNX-N250UBE User Manual 4.6. Wi-Fi Protect Setup 4.6.1 Method 1 PIN Input Config (PIN) 1.
Wireless N Adapter RNX-N250UBE User Manual WPS config page 2. Click Pin Input Config(PIN) 3.
Wireless N Adapter RNX-N250UBE 4. User Manual Please wait when the PIN Method Window pop-up appear, the secure connection between AP and wireless NIC will be founded automatically. 4.6.2 Method 2 Push Button 1. Click Push Button Config(PBC) on Wi-Fi Protect Setup page 2.
Wireless N Adapter RNX-N250UBE 3. User Manual Please wait when the PBC method window pop-up appear, the secure connection between AP and wireless NIC will be founded automatically. Remark If there is more than one AP on the PBC mode, there will be session overlap. Please using method 1 PIN Input Config(PIN) or wait for a while push the button again.
Wireless N Adapter RNX-N250UBE User Manual FAQ This chapter provides solutions to problems that may occur during the installation and operation of the Wireless USB Adapter. Read the descriptions below to solve your problems. 1. The Wireless USB Adapter does not work properly. Reinsert the Wireless USB Adapter into your PC’s USB slot. Right click My Computer and select Properties. Select the device manager and click on the Network Adapter. You will find the Adapter if it is installed successfully.
Wireless N Adapter RNX-N250UBE User Manual clients from trying to establish a BSS at the same time, which can result in multiple singular BSSs being established, rather than a single BSS with multiple clients associated to it. Check that the Network Connection for the wireless client is configured properly. If Security is enabled, make sure that the correct encryption keys are entered on both the Adapter and the access point. Thank you for purchasing a quality Rosewill Product.