Wireless Router RNX-EasyN400 User Manual
Wireless RouterRNX-EasyN400 User Manual Safety Warning • • • • • • • • • • • • • • • • • Place connecting cables carefully so that no one will step on them or stumble over them. Always disconnect all cables from this device before servicing or disassembling. Use ONLY an appropriate power adaptor or cord for your device. Connect the power adaptor or cord to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe).
Wireless RouterRNX-EasyN400 User Manual Table of Contents TABLE OF CONTENTS .......................................................................................................................2 BEFORE WE BEGIN ............................................................................................................................4 1 INTRODUCTION ........................................................................................................................5 1.1 OVERVIEW.....................
Wireless RouterRNX-EasyN400 User Manual 3.7.1 Advanced .................................................................................................................................. 58 3.7.2 Demilitarized Zone (DMZ) ....................................................................................................... 58 3.7.3 Denial of Service (DoS) ............................................................................................................ 59 3.7.4 MAC Filter.........................
Wireless RouterRNX-EasyN400 User Manual Before We Begin • Please configure RNX-EasyN400 with the computer that was last connected directly to your modem. • You can only use the Ethernet port on your modem. If you were using the USB connection before using RNX-EasyN400, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on RNXEasyN400, and then turn the modem back on.
Wireless RouterRNX-EasyN400 User Manual 1 Introduction 1.1 Overview Congratulations on your purchase of RNX-EasyN400 Wireless Network Broadband Router. RNX-EasyN400 is compatible with 802.11g & 802.11b and draft 802.11n v2.0. RNX-EasyN400 is not only a Wireless Access Point, but also doubles as a 4-port fullduplex Switch that connects your wired-Ethernet devices together at incredible speeds.
Wireless RouterRNX-EasyN400 User Manual enhance security Make wireless AP and Bridge mode WDS (Wireless Distribution System) simultaneously as a wireless repeater ** Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual throughput may vary. Network conditions and environmental factors lower actual throughput rate. All specifications are subject to change without notice. 1.
Wireless RouterRNX-EasyN400 User Manual 1.4 Product Layout and LED Signal LED Color Status On POWER Amber Blinking Off On Description RNX-EasyN400 is receiving power and functioning properly. RNX-EasyN400 is performing test or reset RNX-EasyN400 is not receiving power RNX-EasyN400 is ready, but not sending/receiving wireless signals RNX-EasyN400 is sending/receiving wireless signals WLAN/WPS Blue Blinking RNX-EasyN400 is connecting WPS with a wireless client.
Wireless RouterRNX-EasyN400 User Manual Blinking LAN 1~4 port Blue RNX-EasyN400 is sending/receiving data through WAN Off The WAN is not ready or fail On RNX-EasyN400 has a successful Ethernet connection. Blinking Off RNX-EasyN400 is sending/receiving data through LAN port The LAN is not ready or fail Press this button for 1 second to set up a wireless connection via WiFi Protected Setup with WPS another WPS-enabled client.
Wireless RouterRNX-EasyN400 User Manual 1.7 RNX-EasyN400’s LAN & WAN Cable Connection Setup WAN connection: Connect Ethernet cable between WAN ports of your ADSL/CABLE modem & INTERNET port of RNX-EasyN400. Make sure your ADSL/CABLE modem is working well. Contact your ISP if you have any questions. RNX-EasyN400 Rear View + Intnernet plugin RNX-EasyN400 WAN Connection Diagram LAN connection: Connect Ethernet cable between your PC/Notebook LAN port & one of the 4 available LAN ports on RNX-EasyN400.
Wireless RouterRNX-EasyN400 User Manual RNX-EasyN400 LAN Connection Diagram 10
Wireless RouterRNX-EasyN400 User Manual 2 Setup Wizard We will introduce the Smart Wizard in this section. Please make sure the following before insert the CD into the CD/DVD drive: • Internet connection should be setup & ready to use (ADSL or cable modem). • Modem must provide a RJ45 port to connect with RNX-EasyN400. ¾ Please refers to previous page’s “RNX-EasyN400 LAN Connection Diagram“ • Microsoft Windows compatible PC/Notebook with UPnP enabled network adapter.
Wireless RouterRNX-EasyN400 User Manual Click User Manual to open user manual. Click Adobe Reader to install Adobe Acrobat reader on your PC/Notebook. Click EXIT anytime you want to abort. 2.2 Setup Wizard – Configuration Click to proceed. Click to abort. RNX-EasyN400 should be setup as depicted above.
Wireless RouterRNX-EasyN400 User Manual Make sure your DSL/CABLE modem is setup and working. Else take the help of your internet service provider. Click to proceed. Check the MODEM and RNX-EasyN400 connection. It should be as shown below. Check power connection for modem as well as RNX-EasyN400. Click to proceed.
Wireless RouterRNX-EasyN400 User Manual Notice the LED will light up at this stage. If not, check your procedures again. Click to configure WAN & Wireless settings.
Wireless RouterRNX-EasyN400 User Manual Then, you will be prompt to RNX-EasyN400 login page User name and password are admin/admin. Click . Your default browser will connect to RNX-EasyN400 Web Server http://192.168.0.1 .
Wireless RouterRNX-EasyN400 User Manual Click to enter mode selection. 2.3 Setup Wizard – Connect Mode Selection This is where you select the mode that RNX-EasyN400 is going to be use and set its configurations. You can choose AP Router Mode is when you want to set RNXEasyN400 as a wireless LAN administrator for your computer or gaming console to connect to. Or you can choose AP Repeater mode is the WDS/Bridge mode which will extend your wireless signal, but does not enable WAN interface.
Wireless RouterRNX-EasyN400 User Manual Depending on your Network setting, Wizard will show you either one of the pages below, the best detecting option will be selected, please click unless you want to manually configure your connecting option. 2.3.1.1 DHCP Mode Selection Smart Wizard has detected DHCP client. Click , you will see the page show below which ask you to configure the host name and MAC address of RNX-EasyN400.
Wireless RouterRNX-EasyN400 User Manual LABEL DESCRIPTION Host Name This is optional. Depending on if your ISP require you to provide this information. Please leave this blank, if you are not sure. MAC address The default value when Click is set to the WAN’s physical interface of the broadband router. Smart Wizard has finished setting up WAN Configuration. Click to proceed. 2.3.1.2 Wireless Security Selection After Click , you should see the page as show below.
Wireless RouterRNX-EasyN400 User Manual Please choose your security level, and enter your desired name for your wireless network (SSID) and security key (Key); Click to proceed. Depending on how you set up RNX-EasyN400, you will see different result pages before you reboot your RNX-EasyN400.
Wireless RouterRNX-EasyN400 User Manual Below is the example page, if you select the highest security to be your RNX-EasyN400 Connecting option. To apply the entire configuration, click . You will see the below count down when clicked. LABEL DESCRIPTION SSID Enter a descriptive name (up to 32 printable 7-bit ASCII characters) for the wireless LAN.
Wireless RouterRNX-EasyN400 User Manual NOTE: After Wireless settings are applied, you need to connect from your WLAN client with the security settings you just finished configuring. Remember to write down the type of security & security key you selected. 2.3.2 AP Repeater Mode AP Repeater mode is the Repeater mode which will extend your wireless signal, but does not enable WAN interface. Setup Wizard will skip WAN Configuration when you select this mode. Click when select AP Repeater Mode.
Wireless RouterRNX-EasyN400 User Manual You should see the below page, click You will see the count down of the system rebooting 2.3.3 Connecting to RNX-EasyN400 in AP Repeater Mode RNX-EasyN400 will restart as a repeater now. However, in order to access to the configuration web page of the repeater, you will need to manually adjust your computer’s IP.
Wireless RouterRNX-EasyN400 User Manual 1. Click on Start > Control Panel > Network and Internet Connections > Network connections. 2. Right-click on the Local Area Connection which represents your network card and selects Properties. 3. Highlight Internet Protocol (TCP/IP) and click Properties. 4. Click to use the B section like below page. You will need to set IP address for default. Example: If RNX-EasyN400’s LAN IP address is 192.168.0.
Wireless RouterRNX-EasyN400 User Manual 192.168.0.X where X is a number between 100 and 200. Make sure that the number you choose is not in use on the network. Set Subnet mask as 255.255.255.0. 5. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). 6. After finish, Click , Then on below page 7. Open your web browser and type in 192.168.0.1 on the address bar. At the login, enter your username and password (default username: admin, password: admin).
Wireless RouterRNX-EasyN400 User Manual 8. You will see the configuration homepage under “REPEATER” mode now.
Wireless RouterRNX-EasyN400 User Manual 3 Accessing RNX-EasyN400 through Web Browser in Router Mode 1. Make sure your RNX-EasyN400 hardware is properly connected and prepare your computer or computer network to connect to the RNX-EasyN400 (refer to the Quick Start Guide). 2. Launch your web browser. 3. Type "http://192.168.0.1" as the website address. Your computer must be in the same subnet in order to access this website address. 4.
Wireless RouterRNX-EasyN400 User Manual 3.1 Resetting the RNX-EasyN400 If you forget your password or IP address, or you cannot access the RNX-EasyN400 through Web Browser, you will need to use the button at the back of the RNX-EasyN400 to reload the factory-default configuration file. This means that you will lose all configurations that you had previously saved, the Username and password will be reset to “admin” and the IP address will be reset to “192.168.0.1”. 3.1.
Wireless RouterRNX-EasyN400 User Manual 3.2.1 Navigating RNX-EasyN400 in AP Router Mode Click on the side menu selection on System, The picture screen below shows the status screen in AP Router Mode. 3.2.1.1 RNX-EasyN400 Side Menu Description Table – AP Router Mode LABEL DESCRIPTION Status This shows the RNX-EasyN400’s general device, system and interface status information. LAN This is where you can configure LAN IP address, subnet mask, also to enable DHCP server and IP range.
Wireless RouterRNX-EasyN400 Status Internet (For detail, please see Dynamic IP Static IP PPPoE Page 43.) PPTP Basic User Manual This page shows the current Internet connection type and status. This page is only use when your ISP provides you with below information This page is when your ISP assigns you with a fix IP address to connect. This is used when you set your ISP login account name and password in your wireless router instead in your modem or your computer.
Wireless RouterRNX-EasyN400 User Manual servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FTP, Web server etc.) from the Internet. Port tri. ALG UPnP In this section you can configure RNX-EasyN400 to support multiple connections for these types of applications In this section, you can let the selected application to correctly pass through the NAT gateway. This allows you to discover PCs within your intranet for them to easily access through internet.
Wireless RouterRNX-EasyN400 User Manual 3.2.2.1 RNX-EasyN400 Side Menu Description Table – AP Repeater Mode LABEL DESCRIPTION Status This shows the RNX-EasyN400’s general device, system and interface status information. LAN System This is where you can configure LAN IP address, subnet mask, also to enable DHCP server and IP range. (For detail, please see Schedule Page 94.
Wireless RouterRNX-EasyN400 User Manual web-based management Time The Time Zone allows your router to reference or base its time on the settings. DDNS DDNS allows you to map the static domain name to a dynamic IP address. (For detail, Power You can enable or disable Saving power in WLAN mode please see Diagnosis This page could let you diagnosis your current network status. Page 78.) Firmware This page allows you to upgrade RNX-EasyN400’s firmware.
Wireless RouterRNX-EasyN400 User Manual 3.3 RNX-EasyN400’s System Page 3.3.1 Status This page allows you to monitor the current status of your router. System: You can see the Uptime, hardware information, serial number as well as firmware version information. WAN Settings: This section displays whether the WAN port is connected to a Cable/DSL connection. It also displays RNX-EasyN400’s WAN IP address, Subnet Mask, ISP Gateway, MAC address and the Primary DNS.
Wireless RouterRNX-EasyN400 User Manual 3.3.2 LAN The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry level user, try accessing a website from your browser. If you can access website without a glitch, just do not change any of these settings. Click at the bottom of this screen to save the changed configurations. LAN IP IP address: 192.168.0.1. It is RNX-EasyN400’s LAN IP address (the “Default Gateway” IP address of your LAN clients).
Wireless RouterRNX-EasyN400 User Manual DHCP Server DHCP Server: This can enable or disable the Dynamic Pool setting. Lease time: This is the lease time of each assigned IP address. Start IP: This is the beginning of the IP pool for DHCP client hosts. End IP: This is the end of the IP pool for DHCP client hosts Domain name: The Domain Name for the existing or customized network. 3.3.3 DHCP View the current LAN clients which are assigned with an IP Address by the DHCPserver.
Wireless RouterRNX-EasyN400 User Manual 36
Wireless RouterRNX-EasyN400 User Manual 3.3.4 Schedule This page allows users to set up schedule function for Firewall and Power Saving. Edit schedule options to allow configuration of firewall and power savings services to take effect. Fill in the schedule and select type of service. Click to keep the settings. The schedule table lists the pre-schedule service-runs. You can select any of the schedule record using the check box.
Wireless RouterRNX-EasyN400 User Manual 3.3.5 Log View operation event log. This page shows the current system log of the Broadband router. It displays any event occurred after system start up. At the bottom of the page, the system log can be saved to a local file for further processing or the system log can be cleared or it can be refreshed to get the most updated information. When the system is powered down, the system log will be cleared if not saved to a local file. 3.3.
Wireless RouterRNX-EasyN400 User Manual 3.3.7 Language This Wireless Router support multiple language, You can select your desired language here.
Wireless RouterRNX-EasyN400 User Manual 3.4 RNX-EasyN400’s Wizard Page Click Wizard to configure the Broadband Router. Setup wizard will be displayed; check that the modem is connected and click . The details please refer to Setup Wizard at .
Wireless RouterRNX-EasyN400 User Manual 3.5 RNX-EasyN400’s Internet Page 3.5.1 Status This page shows the current Internet connection type and status. 3.5.2 Dynamic IP Use the MAC address when registering for Internet service, and do not change it unless required by your ISP. If your ISP used the MAC address of the Ethernet card as an identifier, connect only the PC with the registered MAC address to the broadband router and click the button.
Wireless RouterRNX-EasyN400 User Manual Host Name: This is optional. Please enter only when your ISP provider provides you with this information. MAC address: The default value is set to the WAN’s physical interface of the broadband router. 3.5.3 Static IP If your ISP Provider has assigned a fixed IP address to your internet plan. Please enter the assigned IP address, Subnet mask, Default Gateway IP address, and Primary DNS and Secondary DNS (if available) provided by your ISP provider. 3.5.
Wireless RouterRNX-EasyN400 User Manual Authentication type: Please use default to auto-detect the best type. Type: Enable the Automatic Connection option to automatically re-establish the connection when an application attempts to access the Internet again. Idle Timeout (Available only under Automatic Connection): This is a maximum period of time for which the Internet connection is maintained during inactivity.
Wireless RouterRNX-EasyN400 User Manual 3.6 RNX-EasyN400’s Wireless Page 3.6.1 Basic In this wireless basic setting page, you can set your wireless connection based on Radio, Mode, Band, SSID, and Channel. Radio: You can turn on/off wireless radio. If wireless Radio is off, you cannot associate with AP through wireless. Mode: In this device, we support two operation modes under AP Router Mode. If you choose AP Router Mode, you can select AP or WDS function in the drop-down menu.
Wireless RouterRNX-EasyN400 User Manual 2.4 GHz (B): If all of your clients are 802.11b, select this one. 2.4 GHz (N): If all of your clients are 802.11n, select this one. 2.4 GHz (B+G): Either 802.11b or 802.11g wireless devices are in your environment. 2.4 GHz (G): If all of your clients are 802.11g, select this one. 2.4 GHz (B+G+N): if all 802.11b, 802.11g, or 802.11n wireless devices are in your environment.
Wireless RouterRNX-EasyN400 User Manual Enable SSID: We support upto 4 multiple SSIDs in this device. Please select how many SSIDs you would like to use in your network environment. SSID1~4: ESSID is the name of your wireless network. It might be a unique name to identify this wireless device in the Wireless LAN. It is case sensitive and up to 32 printable characters. You might change the default ESSID for added security.
Wireless RouterRNX-EasyN400 User Manual 3.6.2 WDS with AP Router WDS (Wireless Distribution System), a system that enables the wireless interconnection of access point, allows a wireless network to be extended using multiple APs without a wired backbone to link them. Each WDS AP needs same channel and encryption type settings. MAC address 1~4: Please enter the MAC address(es) of the neighboring APs which participate in WDS. You can enter up to 4 devices now.
Wireless RouterRNX-EasyN400 User Manual 3.6.3 Advanced Advanced function allows you to set your RNX-EasyN400 in advanced wireless options. You should not change these parameters unless you know what effect the changes will have on RNX-EasyN400. Fragment Threshold: This specifies the maximum size of a packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance.
Wireless RouterRNX-EasyN400 User Manual Data Rate: The “Data Rate” is the rate that this access point uses to transmit data packets. The access point will use the highest possible selected transmission rate to transmit the data packets. N Data Rate: The “N Data Rate” is the rate that this access point uses to transmit data packets for N compliant wireless nodes. Highest to lowest data rate can be fixed. Channel Bandwidth: This is the range of frequencies that will be used.
Wireless RouterRNX-EasyN400 User Manual SSID Selection: This broadband router support multiple SSID, you could select and set up the wanted SSID. Broadcast SSID: If you enabled “Broadcast SSID”, every wireless station located within the coverage of the RNX-EasyN400 can discover its signal easily. WMM: Enabling Wi-Fi Multi-Media can supports QoS for experiencing better audio, video and voice in applications.
Wireless RouterRNX-EasyN400 User Manual WEP Encryption When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself and enter it. You can enter four WEP keys and select one of them as a default key. Then AP can receive any packet encrypted by one of the four keys.
Wireless RouterRNX-EasyN400 User Manual Authentication Type: There are two authentication types: "Open System" and "Shared Key". Both AP and wireless client must be configured with the same authentication type. Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit. The larger the key will be the higher level of security is used, but the throughput will be lower.
Wireless RouterRNX-EasyN400 User Manual WPA-Radius Encryption Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP or CCMP (AES) to change the encryption key frequently. Press button when you are done. 3.6.5 Filter This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network.
Wireless RouterRNX-EasyN400 User Manual Enable wireless access control: Enable the wireless access control function. Adding an address into the list Enter the "MAC Address" and "Description" of the wireless station to be added and then click . The wireless station will now be added into the "MAC Address Filtering Table" below. If you are having any difficulties filling in the fields, just click "Reset" and both "MAC Address" and "Description" fields will be cleared.
Wireless RouterRNX-EasyN400 User Manual 3.6.6 WPS (Wi-Fi Protected Setup) WPS is the simplest way to establish a connection between the wireless clients and the wireless router. You don’t have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection. You only need to press a button on both wireless client and wireless router, and the WPS will do the rest for you.
Wireless RouterRNX-EasyN400 User Manual information when connecting to other WPS-enabled wireless devices. SSID: This is the network broadcast name (SSID) of RNX-EasyN400. Authentication Mode: It shows the active authentication mode for the wireless connection. Passphrase Key: It shows the passphrase key that is randomly generated by the wireless router during the WPS process. You may need this information when using a device which doesn’t support WPS.
Wireless RouterRNX-EasyN400 User Manual Communication between Wireless clients: Allow Wireless Client to communicate with other Wireless Client on specific SSID. Communication between Wireless clients and wired clients: Allow Wireless Client to communicate with Wired Client on the switch on specific SSID. Or Wireless Client will allow to communicate with other Wireless Client and access WAN port only.
Wireless RouterRNX-EasyN400 User Manual 3.7 RNX-EasyN400’s Firewall Page The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ). Note: To enable the Firewall settings select Enable and click 3.7.
Wireless RouterRNX-EasyN400 User Manual server re-directs a particular service/Internet application (e.g. FTP, websites) to a particular LAN client/server, whereas DMZ re-directs all packets (regardless of services) from your WAN IP address to a particular LAN client/server.
Wireless RouterRNX-EasyN400 User Manual Discard Ping From WAN: RNX-EasyN400’s WAN port will not respond to any Ping requests Port Scan: Protects RNX-EasyN400 from Port Scans. Sync Flood: Protects RNX-EasyN400 from Sync Flood attack. 3.7.4 MAC Filter If you want to restrict users from accessing certain Internet applications / services (e.g. Internet websites, email, FTP etc.), and then this is the place to set that configuration. MAC Filter allows users to define the traffic type permitted in your LAN.
Wireless RouterRNX-EasyN400 User Manual Fill in “LAN MAC Address” and of the PC that is allowed / denied to access the Internet, and then click . If you find any typo before adding it and want to retype again, just click and the fields will be cleared. Remove PC MAC Address If you want to remove some PC from the "MAC Filtering Table", select the PC you want to remove in the table and then click .
Wireless RouterRNX-EasyN400 User Manual Deny: If you select “Deny” then all clients will be allowed to access Internet except for the clients in the list below. Allow: If you select “Allow” then all clients will be denied to access Internet except for the PCs in the list below. Add PC IP Address You can click PC to add an access control rule for users by an IP address or IP address range.
Wireless RouterRNX-EasyN400 User Manual Fill in “URL/Keyword” and then click . You can enter the full URL address or the keyword of the web site you want to block. If you happen to make a mistake and want to retype again, just click "Reset" and the field will be cleared. Remove URL Keyword If you want to remove some URL keywords from the "Current URL Blocking Table", select the URL keyword you want to remove in the table and then click .
Wireless RouterRNX-EasyN400 User Manual 3.8 RNX-EasyN400’s Advanced Page 3.8.1 Network Address Translation (NAT) Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses. NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for key services such as Websites and FTP. Select Disable to disable the NAT function. 3.
Wireless RouterRNX-EasyN400 User Manual Enable Port Mapping: Enable or disable port mapping function. Description: description of this setting. Local IP: This is the local IP of the server behind the NAT firewall. Protocol: This is the protocol type to be forwarded. You can choose to forward “TCP” or “UDP” packets only, or select “BOTH” to forward both “TCP” and “UDP” packets. Port Range: The range of ports to be forward to the private IP.
Wireless RouterRNX-EasyN400 User Manual D. If you want to remove all Port Mapping settings from the table, click button. Click will clear your current selections. Click at the bottom of the screen to save the above configurations. 3.8.3 Port Forwarding (Virtual Server) Use the Port Forwarding (Virtual Server) function when you want different servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FTP, Web server etc.
Wireless RouterRNX-EasyN400 User Manual Protocol: Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default “both” setting. Public Port enters the service (service/Internet application) port number from the Internet that will be redirected to the above Private IP address host in your LAN Network. Public Port: Port number will be changed to Local Port when the packet enters your LAN Network.
Wireless RouterRNX-EasyN400 User Manual Enable Trigger Port: Enable or disable the Port Trigger function. Trigger Port: This is the outgoing (Outbound) range of port numbers for this particular application. Trigger Type: Select whether the outbound port protocol is “TCP”, “UDP” or “BOTH”. Public Port: Enter the In-coming (Inbound) port or port range for this type of application (e.g.
Wireless RouterRNX-EasyN400 User Manual Add Port Triggering Fill in the "Trigger Port", "Trigger Type”, “Public Port”, "Public Type", "Public Port" and "Description" of the setting to be added and then Click . The Port Triggering setting will be added into the "Current Trigger-Port Table" below. If you happen to make a mistake, just click and the fields will be cleared.
Wireless RouterRNX-EasyN400 User Manual 3.8.6 UPnP With UPnP, all PCs in you Intranet will discover this router automatically. So, you don’t have to configure your PC and it can easily access the Internet through this router. Enable/Disable UPnP: You can enable or Disable the UPnP feature here. After you enable the UPnP feature, all client systems that support UPnP, like Windows XP, can discover this router automatically and access the Internet through this router without having to configure anything.
Wireless RouterRNX-EasyN400 User Manual This can put the packets of specific protocols in High/Low Queue. The packets in High Queue will process first. Unlimited Priority Queue: The LAN IP address will not be bounded in the QoS limitation. High/Low Priority Queue: This can put the packets in the protocol and port range to High/Low QoS Queue.
Wireless RouterRNX-EasyN400 User Manual This can reserve / limit the throughput of specific protocols and port range. You can set the upper bound and Lower bound. Type: Specify the direction of packets. Upload, download or both. IP range: Specify the IP address range. You could also fill one IP address Protocol: Specify the packet type. The default ALL will put all packets in the QoS priority Queue. Port range: Specify the Port range. You could also fill one Port.
Wireless RouterRNX-EasyN400 User Manual Destination LAN IP: Specify the destination LAN IP address of static routing rule. Subnet Mask: Specify the Subnet Mask of static routing rule. Default Gateway: Specify the default gateway of static routing rule. Hops: Specify the Max Hops number of static routing rule. Interface: Specify the Interface of static routing rule. 3.9 RNX-EasyN400’s Tools Page 3.9.
Wireless RouterRNX-EasyN400 User Manual You can change the password required to log into the broadband router's system webbased management. By default, the password is: admin. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Old Password: Fill in the current password to allow changing to a new password.
Wireless RouterRNX-EasyN400 User Manual Host Address: This is the IP address of the host in the Internet that will have management/configuration access to the Broadband router from a remote site. If the Host Address is left 0.0.0.0 this means anyone can access RNX-EasyN400’s web-based configuration from a remote location, providing they know the password. Port: The port number of the remote management web interface. Enabled: Check to enable the remote management function.
Wireless RouterRNX-EasyN400 User Manual Time Zone: Select the time zone of the country you are currently in. RNX-EasyN400 will set its time based on your selection. NTP Time Server: RNX-EasyN400 can set up external NTP Time Server. Daylight Savings: RNX-EasyN400 can also take Daylight Savings into account. If you wish to use this function, you must select the Daylight Savings Time period and check/tick the enable box to enable your daylight saving configuration.
Wireless RouterRNX-EasyN400 User Manual 3.9.3 DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. This router supports DynDNS, TZO and other common DDNS service providers. Enable/Disable DDNS: Enable or disable the DDNS function of this router Server Address: Select a DDNS service provider Host Name: Fill in your static domain name that uses DDNS.
Wireless RouterRNX-EasyN400 User Manual 3.9.5 Diagnosis This page could let you diagnosis your current network status. By entering any website address, you will know if the internet connection is connected. 3.9.6 Firmware This page allows you to upgrade RNX-EasyN400’s firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page.
Wireless RouterRNX-EasyN400 User Manual Once you’ve selected the new firmware file, click at the bottom of the screen to start the upgrade process Caution: • To upgrade firmware, please make sure the wireless connection is disabled and the computer is connected with a cable to the router. • Also make sure the computer and the wireless router are both plug-in with power adapter during this whole process Step 1 Download the latest firmware from the Rosewill website at www.rosewill.com.
Wireless RouterRNX-EasyN400 User Manual Step 2 Log on to the management web page of the AP. By default, the management IP is http://192.168.0.1 , and the user name is “admin”; password is “admin” . Step 3 Click and , then Click . Step 4 Select the latest firmware that you saved and unzipped onto your computer.
Wireless RouterRNX-EasyN400 User Manual Step 5 Click button. Step 6 Click button for writing the latest firmware to your router. Step 7 Click button. 3.9.7 Back-up This page allows you to save the current router configurations. When you save the configurations, you also can re-load the saved configurations into RNX-EasyN400 through the Restore Settings. If extreme problems occur you can use the Restore to Factory Defaults to set all configurations to its original default settings.
Wireless RouterRNX-EasyN400 User Manual 82
Wireless RouterRNX-EasyN400 User Manual 4 Repeater Mode Repeater mode has limited settings compared to the AP mode. Choose “Repeater mode” on the top right corner of the configuration page. System will counting down and restarts automatically. Before your computer connected to the RNX-EasyN400 in AP Repeater Mode, you will need to manually setup your computer’s IP address, in order to login to the web configure page. In Windows XP: 1.
Wireless RouterRNX-EasyN400 2. User Manual Right-click on the Local Area Connection which represents your network card and selects Properties. 3. Highlight Internet Protocol (TCP/IP) and click Properties. 4. Click to use the B section like below page. You will need to set IP address for default. Example: If RNX-EasyN400’s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X (X is a number between 100 and 200). Make sure that the number you choose is not in use on the network.
Wireless RouterRNX-EasyN400 User Manual 5. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). 6. After finish, Click , Then on below page 7. Open your web browser and type in 192.168.0.1 on the address bar. At the login, enter your username and password (default username: admin, password: admin).
Wireless RouterRNX-EasyN400 8. User Manual You will see the configuration homepage under “Repeater mode” now. Note: After finishing co figurate your RNX-EasyN400 in Repeater mode, please do remember to adjust your computer’s IP address function back to DHCP function.
Wireless RouterRNX-EasyN400 User Manual 4.1 RNX-EasyN400 in Repeater Mode’s System page 4.1.1 Status This page allows you to monitor the current status of your RNX-EasyN400 in Repeater mode. System: You can see the Uptime, hardware information, serial number as well as firmware version information. LAN Settings: This section displays the Broadband router LAN port’s current information. It also shows whether the DHCP Server function is enabled / disabled.
Wireless RouterRNX-EasyN400 User Manual The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry level user, try accessing a website from your browser. If you can access website without a glitch, just do not change any of these settings. Click at the bottom of this screen to save the changed configurations. IP address: This is RNX-EasyN400’s LAN IP address (Your LAN clients default gateway IP address). It can be changed based on your own choice.
Wireless RouterRNX-EasyN400 User Manual The schedule table lists the pre-schedule service-runs. You can select any of them using the check box. 4.1.4 Log View operation log of RNX-EasyN400. This page shows the current system log of the Broadband router. It displays any event occurred after system start up.
Wireless RouterRNX-EasyN400 User Manual 4.1.5 Monitor Show the network packets histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently. 4.1.6 Language This Wireless Router support multiple language of web pages, you could select your native language here.
Wireless RouterRNX-EasyN400 User Manual 91
Wireless RouterRNX-EasyN400 User Manual 4.2 RNX-EasyN400 in Repeater Mode’s Wizard page Click Wizard to configure the Broadband Router. Setup wizard will be displayed; check that the modem is connected and click . The details please refer to Setup Wizard at . 4.3 RNX-EasyN400 in Repeater Mode’s Wireless Page This is where you select the Wireless Router that you want RNX-EasyN400 to receive from and broadcast.
Wireless RouterRNX-EasyN400 User Manual You will see that when add SSID # 2 and SSID #3, you have “Security” in option to set up for your SSID #2 and SSID #3. Radio: This is where you set your RNX-EasyN400 to broadcast the signal from your wireless router.
Wireless RouterRNX-EasyN400 User Manual Mode: This is predefined as Repeater. Band: Depending on the wireless router you want to connect to, you will need to adjust the band accordingly to the wireless router. Enable SSID #: By default, RNX-EasyN400 has 1 set of SSID in Repeater mode. However, you can add two more SSIDs for your designate groups to link to. SSID 1: This is the default SSID #. It will automatically adjust when you select your desired signal to broadcast.
Wireless RouterRNX-EasyN400 User Manual Once selected your desired SSID connection, Click , then you will see below page popup. Depending on the wireless signal that you want to connect to, RNX-EasyN400 will automatically configures to the current Encryption based on WEP, WPA and WPA2.
Wireless RouterRNX-EasyN400 User Manual All you have to do is to enter the password of the wireless router you want to connect with. Then Click You will see the RNX-EasyN400 start countdown and below page appear: Once complete, if successful, you should be the below message: Your RNX-EasyN400 is now ready to broadcast your wireless router’s signal and extend your wireless router’s range.
Wireless RouterRNX-EasyN400 User Manual 5 PC Network Adapter setup (Under Windows XP) • Enter [Start Menu] Æ select [Control panel] Æ select [Network].
Wireless RouterRNX-EasyN400 User Manual • Select [Internet Protocol (TCP/IP)] =>Click [Properties]. • Select the [General] tab and Click “a” on both selections. a. RNX-EasyN400 supports [DHCP] function, please select both [Obtain an IP address automatically] and [Obtain DNS server address automatically].
Wireless RouterRNX-EasyN400 User Manual 99
Wireless RouterRNX-EasyN400 User Manual Appendix A – Product Specification Hardware Feature Dimensions 125mm (L) x 98mm (W) x 25mm (H) WAN: One 10/100 Fast Ethernet RJ-45 LAN: Four 10/100 Fast Ethernet RJ-45 Physical Interface Reset button Power Jack WPS button (WiFi Protected Setup) Power Status WAN (Internet connection) LEDs Status 10/100Mbps LAN1~LAN4 WLAN (Wireless connection) Power Supply: 200 to 240 VDC ± 10％ (ETSI) 100 to 120 VDC ± 10％ (FCC) Power Requirements Device: 12V/1A The reset button is
Wireless RouterRNX-EasyN400 User Manual 101
Wireless RouterRNX-EasyN400 User Manual Appendix B – Troubleshooting Q: How do I configue to set up Remote Management? A: Depending on your internet connect plans, your methods of setting up remote management will be different. 1. After Login to the RNX-EasyN400 management page, Click 「Tools」, then 「Admin」. We should see as below. 2. Host Address is referring a set of IP address that represent the designated computer in your network which you allow to access to your wireless router.
Wireless RouterRNX-EasyN400 User Manual 5. After RNX-EasyN400 finish reset, please Click “System”, then from “Status” page below you will see under “WAN Settings” which shows your External IP address (where has been red circled under “WAN Settings”). 6. External IP Address is the IP address which assign by your ISP provider to your service. When under dynamic IP plans, this IP address should remain the same unless your ISP resets your external IP address or when you have reboot your Modem.
Wireless RouterRNX-EasyN400 User Manual 7. We suggest that you change the default login name and password to your desired login name and password which are difficult for others to guess or hack. (Rosewill default login/Password is admin) 8. Use above picture as an example. The External IP address is 10.16.196.62. The port number that we set is as 8080 or 80 or 8888. 9. Then to remote access to your wireless router: - From a different location, type in 「10.16.196.62:8080」 or 「10.16.196.62:80」 or 「10.16.
Wireless RouterRNX-EasyN400 User Manual Q: What is the IP address of my RNX-EasyN400? A: The default IP address is 192.168.0.1. However If you changed the IP address and have forgotten it, you might get the IP address of RNX-EasyN400 by looking up the IP address of the default gateway for your computer. To do this in most Windows computers, click Start > Run, Type “cmd”, then enter “ipconfig”. The IP address of the Default Gateway might be the IP address of the RNXEasyN400 (depending on the network).
Wireless RouterRNX-EasyN400 • User Manual If you changed the IP address and have forgotten it, see the troubleshooting on how to find the IP address of your RNX-EasyN400. • Make sure your Internet browser does not block pop-up windows and has JavaScripts and Java enabled. • Reset the device to its factory defaults, and try to access the RNX-EasyN400 with the default IP address • If the problem continues, contact the network administrator or Rosewill.
Wireless RouterRNX-EasyN400 User Manual with a battery for when power is lost, i.e. Time Warner Cable Modems, will keep the modem on and connected. Due to the ADSL/Cable modem not assigning the correct DHCP information, the Rosewill Routers can not work correctly and assign a DHCP to the client computers.) • Make sure you entered your ISP account information correctly in the wizard. These fields are case-sensitive, so make sure [Caps Lock] is not on.
Wireless RouterRNX-EasyN400 User Manual that might be interfering with the wireless network (for example, microwaves, other wireless networks, and so on). • Reboot the RNX-EasyN400. • Please update the Wireless Adapter’s Firmware of your Notebook and PC to the latest version to ensure the best connection. • You may consider to activate Qos function, please see section 3.8.7 Quality of Service (QoS) on Page 69. • If problem remainds, please contact the network administrator or Rosewill.
Wireless RouterRNX-EasyN400 User Manual Appendix C – FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Wireless RouterRNX-EasyN400 User Manual Italian: In alcuni Paesi si applicano i requisiti per il funzionamento in interni-esterni, i requisiti di licenza e i canali consentiti, come descritto si seguito: - In Italia l'utente finale deve richiedere una licenza all'Autorità competente nazionale per il funzionamento in esterni del device.
Wireless RouterRNX-EasyN400 User Manual Appendix D – IC Interference Statement Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
