RCM633IS/G3
EN-2 ENGLISH
EN-3
ENGLISH Rosieres Rosieres EN-4
Rosieres Flush installation: Feasible only if the oven is not installed under the counter EN-5
ENGLISH MIJOTER EN-6
EN-7
EN-8 ENGLISH
Power Management Function • • it is possible to set a maximum power absorption level for the induction hob, choosing up to different power ranges. induction hobs are able to limit themselves automatically in order to work at lower power level, to avoid the risk of overloading. To enter Power Management Function Turn on the hob, then Press at the same time the The timer indicator will show “ P5“ which means Pause key and Timer ” power level 5。The default mode is on 7.0kW。 ”.
ENGLISH Touch the pause control “ ”. To exit pause mode Touch the pause control. When the hob is in the pause mode, all the controls are disable except the ON/OFF off with the ON/OFF , you can always turn the induction hob control in an emergency. The hob will shut down after 10min if you don’t exit the pause mode. Locking the Controls • • You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones on).
Touching the “-” and "+” together, the timer is cancelled, and the “00” will show in the minute display. When the time is set, it will begin to count down immediately. The display will show the remaining time and the timer indicator will flash for 5 seconds. Buzzer will beep for 30 seconds and the timer indicator shows “- - “ when the setting time finished.
ENGLISH Other cooking zone will keep operating if they are turned on previously. set more zones: The steps for setting more zones are similar to the steps of setting one zone; When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking zones are on. The minute display shows the min. timer. The dot of the corresponding zone flashes. The shown as below: (set to 15 minutes) (set to 45 minutes) Once the countdown timer expires, the corresponding zone will switch off.
Keep warm Activate the Keep warm function Touching the heating zone slider control , and a indicator next to the key will flash. Touching the keep warm control “ | ”. , the zone indicator show Cancel the keep warm function Touching the heating zone slider control that you want to cancel keep warm. Mijote Activate the Mijote function Touching the heating zone slider control , and a indicator next to the key will flash. Touching the Mijote control “ || ”.
ENGLISH Selection of cooking vessels Iron oil frying Stainless steel Iron pan Iron kettle Enamel Enamel cooking stainless steel utesil kettle Iron plate You may have a number of different cooking vessels 1. This induction hob can identify a variety of cooking vessels, which you can test by one of the following methods: Place the vessel on the cooking zone. If the corresponding cooking zone displays a power level, then the vessel is suitable.
5. If the ferromagnetic part covers only partially the base of the pan, only the ferromagnetic area will heat up, the rest of the base may not heat up a sufficient temperature for cooking. 6. If the ferromagnetic area is not homogeneous, but presents others material such as aluminum this may affect the heating up and the pan detection. If the base of the pan is similar to the pictures below the pan could be not detected.
EN-16 ENGLISH
EN-17
EN-18 ENGLISH
RCM633IS/G3 189,7 174,7 189,9 184,8 EN-19
FR-2 FRENCH
FR-3
FR-4 FRENCH
Rosieres FR-5
FRENCH Installation affleurante: possible uniquement si le four n'est pas installé sous le comptoir FR-6
FR-7
FR-8 FRENCH
Power Management: • Il est possible de limiter la puissance maximale de la table de cuisson et choisir le niveau auquel la table de cuisson sera limitée. Instructions pour activer le power management Allumer la table de cuisson et appuyer en meme temps sur le bouton «+» et le bouton «pause» du timer. L’écran du timer affichera P5, qui indique le niveau 5. C’est le réglage par defaut il est équivalent a 7.
Il y a 5 niveaux possibles de P1 à P5. P1: maximum 2.5kW P2: maximum 3.5kW P3: maximum 4,5kW P4: maximum power 5,5kW P5: maximum power 7,0kW Appuyer sur «+» ou «-» du timer or Confirmation & sortie du mode power managemnt Appuyer en meme temps sur le bouton pause et «+» du timer pour confirmer.
Timer Control: Le timer peut s’utiliser de deux manières différentes: • Comme un simple minuteur qui fonctionne seul Comme un minuteur lié à une zone de cuisson et qui en commande l’extinction quand le temps • programmé s’est écoulé a) Utilisation du timer comme un minuteur (ne selectionnant aucune zone) S’assurer que la table de cuisson soit allumée Appuyer sur «+» de l’écran du timer. Le display se mettra à clignoter indiquant le numero 10.
Quand le minuteur est réglé il partira immédiatement. Le display montrera le temps restant. Note: Un point rouge apparaitra à coté de la puissance de la zone sur laquelle le timer a été programmé.
Fonction: Maintien au chaud Activer la fonction de maintien au chaud En touchant le slider de la zone de cuisson désirée… le niveau de cuisson apparaitra et clignotera En appuyant sur l’icone Maintien au chaud « de puissance de la zone affichera « I » » l’indicateur Désactiver la fonction de maintien au chaud Toucher le slider de la zone où la fonction de maintien au chaud a été activée et cette dernière se désactivera.
FRENCH Choix des récipients de cuisson Poêle à frire en fer Casserole en acier inoxydable Poêle en fer Bouilloire Bouilloire en Ustensile de en fer acier inoxydable cuisson émaillé émaillé Plaque en fer Vous pouvez avoir plusieurs récipients de cuisson différents 1. Cette plaque à induction peut détecter plusieurs récipients de cuisson que vous pouvez tester par l’une des méthodes suivantes : Placer le récipient sur la zone de cuisson.
5. Si la partie ferromagnétique couvre seulement partiellement le fond de la casserole, seule la zone ferromagnétique chauffera, le reste du fond pourrait ne pas chauffer à une température suffisante pour la cuisson. 6. Si la zone ferromagnétique n’est pas homogène mais est constituée d’autres matériaux comme de l’aluminium, cela peut affecter la mise en température et la détection de la casserole. Si le fond de la casserole ressemble aux images ci-dessous, la casserole pourrait ne pas être détectée.
FR-16 FRENCH
FR-17
FR-18 FRENCH
RCM633IS/G3 189,7 174,7 189,9 184,8 FR-19