User Manual
Table Of Contents
- United States of America — FCC Part 15
- Canada
- Europe
- International
- Contents
- Features
- Clean Feed Output
- Custom Controls
- Device Control
- DVE (Fly Key)
- Effects Dissolve
- General Purpose Interface (GPI)
- LiveEDL
- Matte/Wash Generator
- ME Effect System
- Media-Store
- MediaManager
- MediaWipe
- MemoryAI Recall Mode
- Memory System
- MiniME™
- MultiScreen
- MultiViewer
- Pattern and Matte/Wash Generators
- Tally Outputs
- UltraChrome
- Control Panel Overview
- Menu System
- Switcher Basics
- DashBoard
- ViewControl
- Transitions
- Patterns, Washes, and Mattes
- Keying
- Memory Functions
- Memory Access Mode
- Storing Memories
- Recalling Memories
- Memory Recall Mode
- Memory Attributes
- To Set the Program Bus Source Attribute
- To Set the Preset Bus Source Attribute
- To Set the Transition Type Attribute
- To Set the Next Transition Attribute
- To Set the Run Auto Trans Attribute
- To Set the Shared Pattern Generator Attribute
- To Set the Key Bus Sources Attribute
- To Set the Key On-Air Attribute
- To Set the Key Type Attribute
- To Set the Key Mask Attribute
- To Set the Media-Store Attribute
- To Set the Aux Bus Attribute
- To Set the Camera Shot Attribute
- To Set the Roll GPO Attribute
- To Set the Roll VTR Attribute
- Clear Memories
- Switcher Sets
- Media-Store
- Custom Controls
- Switcher Soft Reset
- Glossary
- Index
ViewControl
The ViewControl interface through DashBoard allows
you to coordinate control of the Carbonite switcher,
XPression Live Graphics System, and the BlackStorm
Playout Server all through a touchscreen interface.
Through ViewControl you can select sources, perform
transitions, and run custom controls.
Keep the following in mind when working with
ViewControl
• ViewControl requires DashBoard 5.1, or later.
• Only the sources assigned to the MultiViewer boxes
are available for direct selection. Custom controls
can be used to select other sources.
• A running custom control, or a custom control that
is paused or held, are not shown on the ViewControl
interface.
• The control panel does not follow key and bus
selections made on ViewControl.
ViewControl Overview
The ViewControl interface provides quick access to a
number of custom control buttons as well as the transition
functionality of the switcher.
Custom Control Buttons
The custom control buttons can be assigned to any
custom control on the switcher and given unique names
and icons. The button groups on the left (shown below)
are organized into groups, or tabs.
Figure 11: Custom Control Buttons
Bus Selection Buttons
The bus selection buttons allow you to select the different
buses on different ME outputs of the switcher.
To select a source on a bus, press the bus selection button,
and press the MultiViewer box for the source you want
to select. For example, to select camera 1 on ME 2 Key
3, press M2 K3 and then press the box for the camera 1
source.
Figure 12: Bus Selection Buttons
Keyer Transition Buttons
The Keyer Transition buttons allow you to perform a cut
or dissolve of the keys on the Program bus, without
having to include them as part of the next transition.
These buttons act the same as the Keyer Transition
Buttons on the control panel.
Tip: The Cut buttons turn red when a key is on-air.
Figure 13: Keyer Transition Buttons
Transition Buttons
The transition buttons allow you to select what is
included in the next transition, what type of transition is
to be performed, and perform the transition. These
buttons function similarly to the buttons in the Transition
Area on the control panel.
Tip: The Transition Buttons on ViewControl only control the
transition area of ME 2. To control ME 1 you can create a custom
control to perform the effect you want and assign it to one of the
custom control buttons.
Figure 14: Transition Buttons
Carbonite Black Solo Operation Manual (v1.2) — ViewControl • 19