User Manual

DescriptionLocationEvent
3. Click the Parameter button and
select Size.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new size in the Value
(%) field.
Select the x-axis position of the DVE
key on the selected key for the
selected ME.
Switcher >
Keyer > DVE
Param
DVE Key
X-Position
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
3. Click the Parameter button and
select X-Pos.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new position in the
Value (%) field.
Select the y-axis position for the DVE
key on the selected key for the
selected ME.
Switcher >
Keyer > DVE
Param
DVE Key
Y-Position
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
3. Click the Parameter button and
select Y-Pos.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new position in the
Value (%) field.
Reset the parameters or direction and
flip-flop for the DVE wipe transition of
the selected ME.
Switcher >
Transition >
DVE Wipe
Reset
DVE Wipe, Reset
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click Reset to reset the DVE
wipe parameters.
Select whether the DVE wipe reverses
direction for every second transition of
the selected ME.
Switcher >
Transition >
DVE Wipe
Direction
DVE Wipe Direction
(Flip-Flop)
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
DescriptionLocationEvent
will not be available when you
reset the parameter.
3. Click Flip-Flip.
4. Click On or Off to select whether
Flip-Flop is on (On) or not (Off).
Select the direction for the DVE wipe
transition of the selected ME.
Switcher >
Transition >
DVE Wipe
Direction
DVE Wipe Direction
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
3. Click Direction.
4. Click Forward or Reverse to
select whether the DVE wipe
moves in a forward (Forward)
or reverse (Reverse) direction.
Select the pattern you want to use for
a DVE wipe transition of the selected
ME.
Switcher >
Transition >
DVE Wipe
Effect
DVE Wipe Pattern
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Effect button and
select the pattern you want to
use for the DVE wipe.
Select whether EmbeddedTriggers is
enabled or not for the selected output.
Switcher
Installation >
Embedded
EmbeddedTriggers
— Enable
1. Click the Output button and
select the output BNC that you
Trigger >
Enable
want to send EmbeddedTriggers
commands on.
2. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
3. Click a Value button to select
whether EmbeddedTriggers
commands are inserted for the
selected output (On) or not (Off).
Select the custom control to insert into
the EmbeddedTriggers message.
Switcher
Installation >
Embedded
EmbeddedTriggers
— Insert Trigger
1. Enter the custom control bank in
the Bank field.
Trigger >
Trigger CC
2. Enter the custom control in the
CC field.
Select the data identifier word (DID)
you want to use for the
EmbeddedTriggers message.
Switcher
Installation >
Embedded
Trigger >
Settings
EmbeddedTriggers
— Set DID
1. Click DID
2. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
3. Enter the DID value you want to
use in the Value field.
Carbonite Black Solo Operation Manual (v1.2) — Custom Controls • 55