User Manual

DescriptionLocationEvent
Select a layout for the selected
MultiViewer.
MultiViewer >
MV Layout
MultiViewer —
Layout
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click the Layout button and
select the layout you want to
use.
Select which outputs the MultiViewer
is available on. This feature is only
Switcher
Installation >
Output Mode
MultiViewer —
Outputs
available when the switcher is
operating in a standard-definition or
3G video mode.
1. Click an Outputs button to
select which pair of output BNCs
you want to assign to as
MultiViewer outputs.
2. Click a Lock MultiViewers
button to assign the selected
output BNCs as MultiViewer
outputs (On) or not (Off).
Select how the tallies are shown on
the selected MultiViewer.
MultiViewer >
MV Tally
Display
MultiViewer —
Tally Display
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click a Tally Display button to
select whether tallies are shown
as a border around the box
(Box), as boxes on either side
of the label (Label), or as boxes
on either side of the label but
swapped (Label Reverse).
Assign a source to the selected output
BNC.
Switcher
Installation >
Output
Assignment
Output BNC
Assignment
1. Click the Output button and
select the output BNC that you
want to assign a source to.
2. Click the Source button and
select the source that you want
to assign to the selected output
BNC.
Insert a pause into the custom control.Special > HoldPause CC
1. Enter the length of the pause in
the Pause (fr) field.
Recall a register on the selected PBus
device.
Devices >
PBus
PBus — Recall
1. Click PBus Recall Register.
2. Click the PBus button and select
the device you want to send the
command to.
3. Click the Device button and
select the channel you want to
send the command to.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter number of the register you
want to recall in the Register
field.
DescriptionLocationEvent
Trigger a function on the selected
PBus device.
Devices >
PBus
PBus — Trigger
1. Click PBus Trigger Function.
2. Click the PBus button and select
the device you want to send the
command to.
3. Click the Device button and
select the channel you want to
send the command to.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter the number of the function
you want to trigger in the
Function field.
Have a key removed from the Next
Transition area, so that it is not
Switcher
Personality >
Personality — Auto
Remove Key
included in the next transition, after itAuto Remove
Key has been transitioned off-air using the
KEY X CUT or KEY X AUTO buttons.
1. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
2. Click the Value button and select
whether the personality option is
on (On) or not (Off).
Select how the switcher reacts when
the KEY AUTO button is pressed
during a transition.
Switcher
Personality >
Key Auto
Trans 2nd
Press
Personality — Auto
Trans Second
Press (Key)
1. Click the Second Auto button
and select how the switcher
reacts to pressing the button
during a transition.
• Ignore — the buttons are
ignored during the transition
• Halt Forward — halt the
transition and move forward
through the transition when
pressed again
• Halt Reverse — halt the
transition and move
backwards through the
transition when pressed
again
• Reverse — reverse the
transition immediately
• Cut — cut the transition to
the end
Select how the switcher reacts when
the AUTO TRANS button is pressed
during a transition.
Switcher
Personality >
ME Auto Trans
2nd Press
Personality — Auto
Trans Second
Press (ME)
1. Click the Second Auto button
and select how the switcher
reacts to pressing the button
during a transition.
• Ignore — the buttons are
ignored during the transition
• Halt Forward — halt the
transition and move forward
through the transition when
pressed again
68 • Custom Controls — Carbonite Black Solo Operation Manual (v1.2)