Signal Stand by HD Digital Satellite Receiver HD Digital Receiver User Manual MODEL NUMBER HDR-6110USB Please read this Manual thoroughly before using your Receiver and then retain for future reference.
Contents 1. Important Safety Instructions 1.1 2. 3. 4. 5. 6. Safety Information 1.2 General Information In the Box Controls and Functions 3.1 Front Panel 3.2 Rear Panel 3.3 Remote Control 3.4 Remote Control Functions Installation 4.1 Satellite Dish Installation (REFER TO SEPARATE INSTRUCTIONS) 4.2 Receiver Installation 4.2.1 Connecting your Receiver 4.2.2 Preparing your Remote Control 4.2.3 TV Format Set-Up 4.2.4 Check Satellite Signal Reception 4.2.5 Fast Channel Set-Up Astra 2/A/B/D/Eurobird 1 4.2.
1.0 Important Safety Instructions 1.1 Safety Information • Read these Instructions carefully and retain for future reference. If you sell, or give this Receiver away be sure to pass on the Instructions. • There are no user serviceable parts inside this unit. DO NOT remove the cover there are dangerous voltages inside. Electric shock hazard. • • This unit operates from a 100~240V 50/60Hz Supply. Consumption is ~20W. During use, this device may become warm, this is normal.
1.2 General Information • Thank you for choosing a Ross Digital Satellite TV Receiver. Treated with care and used in accordance with the contents of this manual it will provide many years of reliable service. • This symbol indicates that, at the end of its useful life, this product must not be disposed of with normal domestic waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please recycle it responsibly.
3.0 Controls & Functions: 3.1 Front Panel Signal Stand by HD Digital Satellite Receiver A B C A - Standby Button B - Channel Down Button C - Channel Up Button 3.2 Rear Panel A B C D E F G H A - LNB IN: To connect the input cable from the satellite dish. B - LNB OUT: To connect to another satellite receiver if required. C - USB Socket: To connect an external USB memory device for programme recording. D - HDMI Socket: To connect to a HDTV with an HDMI cable for HD (High definition) viewing.
3.
3.4 Remote Control Functions Button Function 1 POWER: Turns on the power or switches the unit to standby mode 2 TIMER: To select upto 8 timer sequences of your choice. 3 EPI: Shows Now and Next EPG for the programme being viewed. 4 NUMERIC BUTTONS: Enter a number to select a channel directly or to select the menu options. 5 16:9: Adjusts screen format between 16:9 and 4:3. 6 LANG: Press to select OSD language preference. 7 CH +/-: Up and down select for channels. Also used in menu operations.
Button Function 23 SUBTL: Sets broadcast dependant subtitles for the current TV programme. 24 RECALL: Press to switch to previously watched channel. 25 FAV: Select favourite channel list or current channel list in the view mode. 26 TIMESHIFT: (NOT AVAILABLE ON THIS MODEL). 27 PAGE UP/DOWN: Press to jump one page up or down. 28 V-FORMAT: Press to select the video output mode between; 1080I, 720 P and 576P.
4.0 Installation: Introduction This manual will help you learn the basic use of your receiver such as installation, selecting channels and many other functions of the set top box. 4.1 Satellite Dish Installation Please refer to the separate documentation “Satellite Dish Installation Guide” to install your dish. You will need to assemble, erect and roughly align your dish to your chosen satellite before connecting up and turning on your Receiver. 4.2 Receiver Installation 4.2.
4.2.4 Check Satellite Signal Reception • • • • • • Press the Menu Button on the Remote Control. The Installation Menu will be displayed. Using the CH- Button select Antenna Setting and then press OK. Please note that ASTRA 2A/B/D and Eurobird 1 satellite is labelled 4.ASTRA/EURO1. Your Receiver has a large number of the available Satellites already programmed in to make setting up easier for you. You can see the Satellite name at the top right of the OSD (On-Screen Display).
5.0 Menu System: 5.1 Installation Menu In this part of the manual only the basic installation is covered. If you wish to set up your receiver to work with a motorised dish then please refer to SECTION 6, “Advanced Installation”. The MENU provides access to many features and functions which will help to improve your enjoyment of your new product. Press MENU to enter the INSTALLATION Menu, then use the CH-, CH+ keys to select the item you wish to adjust and the VOL-, VOL+ to select the new setting.
5.2.1 TV Channel Edit Using the “VOL-” and “VOL+” buttons you can select from the options of; LOCK, DELETE, MOVE, RENAME, EDIT and SELECT functions to edit your TV programmes. You can press the “CH-” or “CH+” buttons to select the channel, and press “VOL-” or “VOL+” button to choose the functions which are displayed towards the bottom of the OSD. Press the “OK” button to activate your choice. • Parental Lock - To prevent the viewing of channels that are not suitable for Children.
5.2.2 Radio Channel Edit Using the “VOL-” and “VOL+” buttons you can select from the options of; LOCK, DELETE, MOVE, RENAME, EDIT and SELECT functions to edit your Radio programmes. You can press the “CH-” or “CH+” buttons to select the channel, and press “VOL-” or “VOL+” button to choose the functions which are displayed towards the bottom of the OSD. Press the “OK” button to activate your choice. • The procedure for editing Radio channels is identical to that for TV Channels as described in Section 5.2.
5.3.1 System Setting Adjust the SYSTEM SETTINGS to match your TV and other equipment. When finished configuring the settings, press “OK” to save and exit. You will be prompted to confirm your new settings prior to exiting. • TV type: Set your desired Resolution selecting from; 1080i, 720p or 576p It is advised to select 1080i for High Definition. • Screen Mode: To set between 16:9 wide screen and 4:3 TV screen mode, set to Auto as default.
5.3.3 Timer • Press TIMER button 2 to enter directly from the remote control. The TIMER Menu provides access to 8 Timers for you to programme enabling you to switch to your desired programme at a specific time to avoid missing something you want to watch. Using the VOL+, VOL- and CH+, CH- buttons to set the preferred configuration, press the OK button to set the timer, you can also set the preferred Power On mode for TV or Radio.
5.4 User Settings This section allows the setting of PARENTAL CONTROL preferences, OSD settings, details of any connected USB device and finally FACTORY DEFAULT (resets the whole receiver back to how it left the factory). Press MENU and then VOL+ to enter the USER SETTINGS Menu, then use the CH-, CH+ keys to select the item you wish to adjust and the VOL-, VOL+ to select the new setting. 5.4.
5.4.2 OSD Control In this Menu you can Select the preferred MENU LANGUAGE, STANDBY DISPLAY, INFORMATION BAR TIMEOUT and REMOVE TIMESHIFT FILE. • Menu Language: To select the preferred OSD language. “English” is set as the default language. • Standby Display: Turns the Time Display ON or OFF when in Standby Mode. • Information Bar Timeout: To set the timeout period for the Information Bar. • Remove Timeshift File: Removes the Timeshift File. 5.4.
NOTE: Further information on this Procedure is available in SECTION 7. This function MUST be used with EXTREME CAUTION. ONLY Software provided by your Service Centre can be used. Use of other Software may damage your device and invalidate your warranty. During the UPDATE process DO NOT press any buttons or switch the unit off. • Delete: Choose a file with the remote control, and then press the GREEN (ZOOM) button on the remote control to delete the selected file.
6.0 Advanced Installation: This section is aimed at the more experienced Satellite Receiver (Set Top Box) user. Specifically, it describes how to set up your unit to work with a Motorised Dish and how to add additional Satellites that are not present in the Factory pre-loaded list. Press MENU to enter the INSTALLATION Menu, then use the CH-, CH+ keys to select the item you wish to adjust and the VOL-, VOL+ to select the new setting. Then press OK to store. 6.
[1] SCAN Press the RED button “SAT”, to search for channels from the current satellite. [2] ADD SATELLITE Press the GREEN button “ZOOM”, to add a new satellite, configure the settings such as; satellite name, east/west and longitude then press “OK” to save and exit. [3] EDIT SATELLITE Press the YELLOW button “PAUSE”, to edit the current satellite. Edit the satellite name, east/west and Longitude, then press “OK” to save and exit.
[3] TP EDIT Press the YELLOW button “PAUSE” to edit the current TP. Choose the current TP number by “VOL-” or “VOL+” buttons, then input the frequency value and symbol rate value by numeric key, choose the correct Polarization, Horizontal or Vertical then save and exit. [4] DELETE TP Press the BLUE button “TV/RADIO”, to delete the current selected TP. 6.3 Motor Configuration (DiSEqC1.2) This section is used to set up the auto Satellite Dish (DiSEqC1.2 system) location system.
• • User Longitude: Enter your Longitude using the numerical keys • USALS: Set to ON as required. East / West: Select EAST / WEST depending on the Satellite locations Enter the required information as above and then press OK to SAVE and EXIT back to the INSTALLATION MENU. Please refer to your Motorised Dish Installation Manual for further information. 7.0 Software Update: NOTE: This function MUST be used with EXTREME CAUTION. ONLY Software provided by your Service Centre can be used.
8.0 Trouble Shooting: If you have problems with the set top box, please consult the table below because it may be a simple problem that can be solved at home. Plug not inserted correctly. Remove plug and reinsert into the socket. Switch on the back of the set top box is switched off. Check the switch and switch to the on position once all connections are installed. Is the Satellite dish installed correctly. Reinstall the dish and calibrate it. LNB input is not connected correctly.
9.0 Specification 1.Tuner & Modulator Input Frequency: Input Impendence: Input Level: Input socked: LNB Power & Polarization: Current: (short circuit protection) Waveform: Symbol rate: Outer decoder: Code rate: 950MHz to 2150MHz 75 ohms -65dBm to-25dBm F type connector Horizontal:+18V; Vertical: +13V; Max 500mA; QPSK S2 2~45MS/s RS(204,188,8) 1/2,2/3,3/4,5/6,7/8 2.MPEG2 Decoding Transport Stream & Profile Level: MPEG-4/H.
