User's Manual

-2-
conductor cable is required.
5.
The cable shield wire on the reader should be attached to
an Earth g
round (best) or signal ground connection at the
panel or power supply end of the cable. This configuration
is best for shielding the reader cable from external
interference.
TABLE 1: WIRE GAGE SPECIFICATIONS
Distance Gage 5 Conductor 6 Conductor
 200 ft. (61m) 22 Alpha 1295C Alpha 1296C
 300 ft. (91m) 20 Alpha 58126 Alpha 58126
 500 ft. (153 m) 18 Alpha 58136 Alpha 58136
Note: Recommended cable is only a guideline, use any
manufacturer that meets the gage and shield specifications.
HOW TO TEST AND OPERATE THE READER
The reader should be tested after wiring it to a
power supply and the host. Do this by performing
the following steps:
1. Power up the reader. The LED and beeper will
activate three times. This indicates that the
reader is working properly.
2. Present the appropriate type of ID card to the
reader. (See Table 2 for the correct card type
based on the reader model.) The LED will
momentarily flash green and a short beep will
be emitted. This indicates that the card was
read properly by OmniProx.
3. After the card data is processed by the host, the
host can then turn the LED green or yellow.
Refer to the host description of the LED
operation if the reader LED is controlled by the
host.
Table 2: Model Number vs. Feature Matrix
Model
Number
UL Listing
Part #
Card
Type
Output
Format
Read
Range
(Max.) *
OP10-FW AY-K10 HID Wiegand 3”
OP10-AW AY-K12 ADEMCO Wiegand 3”
OP20-FW AY-J10 HID Wiegand 4”
OP20-AW AY-J12 ADEMCO Wiegand 4”
OP30-FW AY-L10 HID Wiegand 5”
OP30-AW AY-L12 ADEMCO Wiegand 5”
OP40-FW AY-H10 HID Wiegand 4”
OP40-AW AY-H12 ADEMCO Wiegand 4”
OP45-FW AY-M10 HID Wiegand 4”
OP45-AW AY-M12 ADEMCO Wiegand 4”
OP90-FW AY-Qxx HID Wiegand 1.5”
Model
Number
UL Listing
Part #
Card
Type
Output
Format
Read
Range
(Max.) *
TABLE 1: WIRE GAGE SPECIFICATIONS
Distance Gage 5 Conductor 6 Conductor
 200 ft. (61m) 22 Alpha 1295C Alpha 1296C
 300 ft. (91m) 20 Alpha 58126 Alpha 58126
 500 ft. (153 m) 18 Alpha 58136 Alpha 58136
Note: Recommended cable is only a guideline, use any
manufacturer that meets the gage and shield specifications.
HOW TO TEST AND OPERATE THE READER
The reader should be tested after wiring it to a
power supply and the host. Do this by performing
the following steps:
1. Power up the reader. The LED and beeper will
activate three times. This indicates that the
reader is working properly.
2. Present the appropriate type of ID card to the
reader. (See Table 2 for the correct card type
based on the reader model.) The LED will
momentarily flash green and a short beep will
be emitted. This indicates that the card was
read properly by OmniProx.
3. After the card data is processed by the host, the
host can then turn the LED green or yellow.
Refer to the host description of the LED
operation if the reader LED is controlled by the
host.
Table 2: Model Number vs. Feature Matrix
Model
Number
UL Listing
Part #
Card
Type
Output
Format
Read
Range
(Max.) *
OP10-FW AY-K10 HID Wiegand 3”
OP10-AW AY-K12 ADEMCO Wiegand 3”
OP20-FW AY-J10 HID Wiegand 4”
OP20-AW AY-J12 ADEMCO Wiegand 4”
OP30-FW AY-L10 HID Wiegand 5”
OP30-AW AY-L12 ADEMCO Wiegand 5”
OP40-FW AY-H10 HID Wiegand 4”
OP40-AW AY-H12 ADEMCO Wiegand 4”