User's Manual
Table Of Contents
- 1. General Information
- 2. Technical Specifications
- 3. Installation
- 4. Wiring Instructions
- 5. Reader Functionality
- 5.1 Transmit Mode
- 5.2 Programming the AYC- F/G/M60 Series
- Programming Menu
- Entering Programming Mode
- Exiting Programming Mode
- Selecting Keypad Transmission Format
- Keypad Transmission Format Option Number
- Option 1: Single Key, 6-Bit Wiegand (Rosslare Format)
- Option 2: Single Key, 6-Bit Wiegand Nibble and Parities
- Option 3: Single Key, 8-Bit Wiegand Nibbles Complemented
- Option 4: 4 Keys Binary + Facility Code, 26-Bit Wiegand
- Option 5: 1 to 5 Keys + Facility Code, 26-Bit Wiegand
- Option 6: 6 Keys BCD and parity bits, 26-Bit Wiegand
- Option 7: Single Key, 3x4 Matrix Keypad (MD-P64)
- Option 8: 1 to 8 Keys BCD, Clock & Data
- Option 9: Single Key, 4-bit Wiegand
- Selecting Proximity Card Transmission Format
- Changing the Programming Code
- Changing the Facility Code
- Setting the Backlight and Reader Format
- Return to Factory Default Settings
- Replacing a Lost Programming Code
- 6. Controller Functionality
- 6.1 Normal, Secure, and Master Users
- 6.2 Modes of Operation
- 6.3 Auxiliary Input & Output
- 6.4 Door Alarms
- 6.5 Internal Case and Back Tamper
- 6.6 Lockout Feature (Keypad / Card Tamper)
- 6.7 Request to Exit (REX) Function
- 6.8 Secure Application Appurtenances
- 6.9 Programming the AYC- F/G/M60
- Programming Menu
- Entering Programming Mode
- Exiting Programming Mode
- Changing Lock Strike Code
- Changing Auxiliary Code
- Changing the Programming Code
- Changing the Normal / Secure Code
- Changing the Normal / Bypass Code and Door Chime Settings
- Setting Fail Safe/Secure Operation, Tamper Siren and Lock Strike Release Time
- Defining the Auxiliary Input and Output
- Quick Reference Guide for Auxiliary Mode Setting
- Detailed Reference Guide
- Setting the Lockout Feature
- Setting the backlight behavior
- Enrolling Primary and Secondary Codes
- Deleting Primary and Secondary Codes
- Relay Codes Assignment
- Relay Code Assignment using Search Method
- Pin Code Length / Factory Default Settings
- Replacing a Lost Programming Code
- Replacing a Lost Normal / Secure Code
Replacing a Lost Programming Code
Note:
• The AYC- F/G/M60 must be in Normal mode, otherwise
this will not work. Make sure that the Mode LED is green
before proceeding.
1) Remove power from the Power Supply Unit.
2) Press the REX Button on the Power Supply Unit.
3) Apply power to the unit with REX button pressed.
4) Release the REX Button.
5) You now have 15 seconds to program a new Programming
code into the Access Control unit using the default code
based on the PIN code length you chose (see Programming
Menu on page 34), before the controller reverts to the
existing code.
Replacing a Lost Normal / Secure Code
Note:
• The AYC- F/G/M60 must be in Secure Mode, otherwise
this will not work. Make sure that the Mode LED is red
before proceeding.
1) Remove power from the Power Supply Unit.
2) Press the REX Button on the Power Supply Unit.
3) Apply power to the unit with the REX button pressed.
4) Release the REX Button.
5) You now have 15 seconds to program a new Normal /
Secure code into the Access Control unit using the default
code based on the PIN code length you chose (see
Programming Menu on page 34), before the controller
reverts to the existing code.
AYC-Qx4 family manual Page 56