User's Manual
Table Of Contents
- 1.2.3.1. Cable & Connector
- 1.2.3.2. Pin Details
- 1.2.3.3. Terminal <- > MCP040 wiring
- 1.2.3.4. Terminal <- > LC015B wiring
- 1.2.3.5. Terminal <- > EM Type Door Lock wiring
- 1.2.3.6. Terminal <- > WIEGAND Device wiring
- 3.1.6.1. Single Type (Door Lock=STRIKE)
- 3.1.6.2. Single Type (Door Lock=MOTOR)
- 3.1.6.3. Single Type (Lock Controller=LC010)
- 3.1.6.4. Single Type (Lock Controller=LC015)
- 3.1.6.5. Dummy Type (RS485=MCP040)
- 3.1.6.6. Network Type (Door Lock=STRIKE)
- 3.1.6.7. Network Type (Door Lock=MOTOR)
- 3.1.6.8. Network Type (Lock Controller=LC010)
- 3.1.6.9. Network Type (Lock Controller=LC015)
- 3.4.1.1. USER TYPE
- 3.4.1.2. AUTH TYPE
- 3.4.1.3. INPUT FP
- 3.4.1.4. INPUT CARD
- 3.4.2.1. AUTO ADD – 1. FP
- 3.4.2.2. AUTO ADD
- 3.6.1.1. TYPE
- 3.6.1.2. AUTO TNA
- 3.6.2.1. Language
- 3.6.2.2. SHOW ID
- 3.6.2.3. USER LOGO
- 3.6.2.4. USER ID LEN
- 3.6.2.5. DATE
- 3.6.3.1. LOG SAVE
- 3.6.3.2. IMAGE SAVE
- 3.6.4.1. RESULT
- 3.6.4.2. NET ERROR
- 3.6.4.3. PING
- 3.7.1.1. 1:1 LEVEL
- 3.7.1.2. 1: N LEVEL
- 3.7.1.3. LFD LEVEL
- 3.7.1.4. AUTH TIME
- 3.8.1.1. LOCK1 type
- 3.8.1.2. LOCK1 OPEN TIME
- 3.8.1.3. LOCK2 type
- 3.8.1.4. LOCK2 OPEN TIME
- 3.8.1.5. OPEN ALARM
- 3.8.1.6. DM0
- 3.8.1.7. DM1
- 3.8.1.8. DM2
- 3.8.2.1. TYPE
- 3.8.2.2. DEV ID
- 3.8.3.1. WIRE-INPUT
- 3.8.3.2. WIRE-OUTPUT
- 3.8.3.3. CUSTOM BIT LENGTH
- 3.8.3.4. SITE CODE
- 3.8.3.5. SEND INFO
- 3.10.1.1. CONFIG
- 3.10.1.2. LOG DB INIT
- 3.10.1.3. FACTORY INIT
- 3.10.2.1. INT DEVICE
- 3.10.2.2. EXT DEVICE
- 3.10.3.1. LOG EXPORT
- 3.10.3.2. USER EXPORT
- 3.10.3.3. USER INPUT
- 3.10.3.4. FW UPDATE
AY-B9250BT User Guide 19
3.1.3. How to access the menu without administrator authentication
This is the method to enter the Menu in exceptional cases such as losing your administrator
card that is registered in the terminal or inability to make a fingerprint authentication because
of absence of administrator.
① Power terminal OFF.
② Disassemble device and make case open state.
③ While case opens, make DIP of rear side switch ON state as follows.
④ Power terminal ON.
⑤ After the terminal completely booted, Press F1 longer to enter the menu with buzzer
sound “Ppiririk”.
★ Caution: You should return DIP SWITCH OFF after modification.
3.1.4. Save Settings
▶ If there are some changes, the following screen appears.
▶ If you select “YES”, then save them with buzzer sound “Ppibibig” and reboot.
▶ If there are no changes, it returns to the previous menu screen.
▶ While changing the settings in the menu, if there is no input for 30 seconds, it returns to
the previous menu.
OFF
ON
ON
1
2