User's Manual
Table Of Contents
- 1.2.3.1. Cable & Connector
- 1.2.3.2. Pin Details
- 1.2.3.3. Terminal <- > MCP040 wiring
- 1.2.3.4. Terminal <- > LC015B wiring
- 1.2.3.5. Terminal <- > EM Type Door Lock wiring
- 1.2.3.6. Terminal <- > WIEGAND Device wiring
- 3.1.6.1. Single Type (Door Lock=STRIKE)
- 3.1.6.2. Single Type (Door Lock=MOTOR)
- 3.1.6.3. Single Type (Lock Controller=LC010)
- 3.1.6.4. Single Type (Lock Controller=LC015)
- 3.1.6.5. Dummy Type (RS485=MCP040)
- 3.1.6.6. Network Type (Door Lock=STRIKE)
- 3.1.6.7. Network Type (Door Lock=MOTOR)
- 3.1.6.8. Network Type (Lock Controller=LC010)
- 3.1.6.9. Network Type (Lock Controller=LC015)
- 3.4.1.1. USER TYPE
- 3.4.1.2. AUTH TYPE
- 3.4.1.3. INPUT FP
- 3.4.1.4. INPUT CARD
- 3.4.2.1. AUTO ADD – 1. FP
- 3.4.2.2. AUTO ADD
- 3.6.1.1. TYPE
- 3.6.1.2. AUTO TNA
- 3.6.2.1. Language
- 3.6.2.2. SHOW ID
- 3.6.2.3. USER LOGO
- 3.6.2.4. USER ID LEN
- 3.6.2.5. DATE
- 3.6.3.1. LOG SAVE
- 3.6.3.2. IMAGE SAVE
- 3.6.4.1. RESULT
- 3.6.4.2. NET ERROR
- 3.6.4.3. PING
- 3.7.1.1. 1:1 LEVEL
- 3.7.1.2. 1: N LEVEL
- 3.7.1.3. LFD LEVEL
- 3.7.1.4. AUTH TIME
- 3.8.1.1. LOCK1 type
- 3.8.1.2. LOCK1 OPEN TIME
- 3.8.1.3. LOCK2 type
- 3.8.1.4. LOCK2 OPEN TIME
- 3.8.1.5. OPEN ALARM
- 3.8.1.6. DM0
- 3.8.1.7. DM1
- 3.8.1.8. DM2
- 3.8.2.1. TYPE
- 3.8.2.2. DEV ID
- 3.8.3.1. WIRE-INPUT
- 3.8.3.2. WIRE-OUTPUT
- 3.8.3.3. CUSTOM BIT LENGTH
- 3.8.3.4. SITE CODE
- 3.8.3.5. SEND INFO
- 3.10.1.1. CONFIG
- 3.10.1.2. LOG DB INIT
- 3.10.1.3. FACTORY INIT
- 3.10.2.1. INT DEVICE
- 3.10.2.2. EXT DEVICE
- 3.10.3.1. LOG EXPORT
- 3.10.3.2. USER EXPORT
- 3.10.3.3. USER INPUT
- 3.10.3.4. FW UPDATE
AY-B9250BT User Guide 34
INPUT CARD 3.4.1.4.
When you check Card as AUTH TYPE, you need to follow steps as below. If you input CARD
on Waiting state, registration completes and INPUT OK screen is displayed.
EM CARD ex) Card No.(5byte): 08h 01h 16h 1Dh D6h
Card Format Card No. Display Method
Standard
02207638
(16001DD6)
(3+5)digits Decimal
[022(16h)+07638(1DD6h)]
SC CARD ex) Card No.(4byte): 52h 9Dh 06h E3h
Card Format
Card No.
Display Method
Standard 529D06E3 8digits Hex
3.4.2. AUTO ADD
AUTO ADD is used when you want to register general users (not admin user) consecutively
with card or fingerprint.
If you select FP, it adds users by increasing ID consecutively only with fingerprint.
If you select CARD, it adds users by increasing ID consecutively only with card.
AUTO ADD – 1. FP 3.4.2.1.
This is the menu when registering the users continuously only by fingerprint.
Input fingerprint in twice and then the registration succeeded. If you want to add more users,
select 2. YES, and continue the registration. User ID increases automatically.