User's Manual
Table Of Contents
- 1.2.3.1. Cable & Connector
- 1.2.3.2. Pin Details
- 1.2.3.3. Terminal <- > MCP040 wiring
- 1.2.3.4. Terminal <- > LC015B wiring
- 1.2.3.5. Terminal <- > EM Type Door Lock wiring
- 1.2.3.6. Terminal <- > WIEGAND Device wiring
- 3.1.6.1. Single Type (Door Lock=STRIKE)
- 3.1.6.2. Single Type (Door Lock=MOTOR)
- 3.1.6.3. Single Type (Lock Controller=LC010)
- 3.1.6.4. Single Type (Lock Controller=LC015)
- 3.1.6.5. Dummy Type (RS485=MCP040)
- 3.1.6.6. Network Type (Door Lock=STRIKE)
- 3.1.6.7. Network Type (Door Lock=MOTOR)
- 3.1.6.8. Network Type (Lock Controller=LC010)
- 3.1.6.9. Network Type (Lock Controller=LC015)
- 3.4.1.1. USER TYPE
- 3.4.1.2. AUTH TYPE
- 3.4.1.3. INPUT FP
- 3.4.1.4. INPUT CARD
- 3.4.2.1. AUTO ADD – 1. FP
- 3.4.2.2. AUTO ADD
- 3.6.1.1. TYPE
- 3.6.1.2. AUTO TNA
- 3.6.2.1. Language
- 3.6.2.2. SHOW ID
- 3.6.2.3. USER LOGO
- 3.6.2.4. USER ID LEN
- 3.6.2.5. DATE
- 3.6.3.1. LOG SAVE
- 3.6.3.2. IMAGE SAVE
- 3.6.4.1. RESULT
- 3.6.4.2. NET ERROR
- 3.6.4.3. PING
- 3.7.1.1. 1:1 LEVEL
- 3.7.1.2. 1: N LEVEL
- 3.7.1.3. LFD LEVEL
- 3.7.1.4. AUTH TIME
- 3.8.1.1. LOCK1 type
- 3.8.1.2. LOCK1 OPEN TIME
- 3.8.1.3. LOCK2 type
- 3.8.1.4. LOCK2 OPEN TIME
- 3.8.1.5. OPEN ALARM
- 3.8.1.6. DM0
- 3.8.1.7. DM1
- 3.8.1.8. DM2
- 3.8.2.1. TYPE
- 3.8.2.2. DEV ID
- 3.8.3.1. WIRE-INPUT
- 3.8.3.2. WIRE-OUTPUT
- 3.8.3.3. CUSTOM BIT LENGTH
- 3.8.3.4. SITE CODE
- 3.8.3.5. SEND INFO
- 3.10.1.1. CONFIG
- 3.10.1.2. LOG DB INIT
- 3.10.1.3. FACTORY INIT
- 3.10.2.1. INT DEVICE
- 3.10.2.2. EXT DEVICE
- 3.10.3.1. LOG EXPORT
- 3.10.3.2. USER EXPORT
- 3.10.3.3. USER INPUT
- 3.10.3.4. FW UPDATE
AY-B9250BT User Guide 62
USER EXPORT 3.10.3.2.
The saved User DB from the terminal saves in USB memory through UDL.
It saves as USER.NDB file.
or
USER INPUT 3.10.3.3.
It reads the user DB from USB memory through UDL and adds it in terminal user DB.
If inputting user DB in the terminal, all existing user DB are deleted.
If you need the existing user DB saved in the terminal, back up first and try to input the user.
It opens USER.NDB file in USB memory and brings into the terminal through UDL.
The user registration data that you brought is reflected in the internal DB and added.
※ CAUTION: If you press F2 Key to stop in READ state, user loading fails.
or
FW UPDATE 3.10.3.4.
It is used when reading the firmware from USB memory through UDL and updating the
terminal firmware.
Firmware proceeds only when there is FW.NFW file name in USB memory.
. or
3.10.4. REBOOT
It is used when rebooting the terminal.