SPN6G (HLX40) Advanced Wireless Security Panel Installation Manual May 2009
Table of Contents Table of Contents 1. INTRODUCTION.....................................................................................................5 1.1 General............................................................................................................................. 5 1.2 Special Features .............................................................................................................. 5 1.3 Information to User .....................................................
Table of Contents 6.2 7. Enrolling Wireless Devices and Remote Controls ..................................................... 19 INSTALLERS MENU ............................................................................................20 7.1 Accessing the Installer Menu ....................................................................................... 20 7.2 Change Code ................................................................................................................. 20 7.
Table of Contents 7.9.3. 7.9.4. 7.9.5. 8. Test Indicators........................................................................................................................................... 38 Sirens test.................................................................................................................................................. 38 Test Devices.........................................................................................................................................
INTRODUCTION 1. INTRODUCTION 1.1 General The HomeLogiXTM panel by Rosslare is the perfect wireless security system for intrusion protection of the home, or small office providing security monitoring and VIP Voice messaging. Users receive the latest RF technology in a wide selection of advanced wireless sensors and remotes, and benefit from smooth and easy operation of a large number of security and communication options.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
HOMELOGIXTM QUICK REFERENCE HOMELOGIXTM QUICK REFERENCE 2. This section provides a description of the control panel and the keypad. In addition, it also describes the chimes emitted when the buttons on the keypad are pressed. 2.1 The Panel Menu Power indicator Enter Status indicator Keypad door Display Local emergency button Local sounder Microphone Figure 1: HomeLogiXTM Panel Menu Use to navigate between menus.
HOMELOGIXTM QUICK REFERENCE 2.2 The Keypad ABC DEF GHI JKL MNO PQRS TUV WXYZ MEM ESC Figure 2: Keypad The following table describes the keypad functions: Key Press to Menu Navigate between User and Installer menus, and Normal mode. Navigate to the next menu or the next option within a menu. Enter Accept an entry or selection. Local When pressed for 3 seconds a standard panic alarm Sounds emergency Keys 0-9 Enter alphanumeric entries. Press 0 to enter a space.
HOMELOGIXTM QUICK REFERENCE 2.2.1. Keypad Operated Functions When the system is idle, the alphanumeric keys initiate the following commands: Press To 0 Memory Display Press once to display the alarms caused during the last arming period per zone. The first line of the displays shows the alarm memory, and the second line shows the zone description, event and time. The display toggles between zone description and the date by pressing the Enter button. Press Menu to display the next alarmed zone.
HOMELOGIXTM QUICK REFERENCE 2.3 Sound Indicators Following are the sounds emitted by the system and push buttons: Sound Sounded when Single beep A key is pressed Long beep An attempt is made to enter an invalid or unacceptable entry Two short beeps Button not pressed for a period of 30 seconds (except during test mode). The system automatically exits the current menu. Three short beeps An entry is successfully accepted.
SPECIFICATIONS 3. SPECIFICATIONS 3.1 RF Data RF Unit Type Integrated RF transceiver (two-way) shielded super heterodyne, fixed frequency Antenna Type Printed PCB type antenna Operating Frequencies 433.92 MHz G series 868.
SPECIFICATIONS 3.4 Communication • Frequencies: 433.92MHz (G version) and 868.
USER MENU STRUCTURE 4. USER MENU STRUCTURE The user menu enables basic user settings such as setting the date and time, and changing user codes. Up to twenty users can access most of the user menu settings, each with their own code, including one master user who has access to all the settings. Settings marked with an (M) can be accessed by the master user only, and appear only if the master code was entered.
INSTALLATION 5. INSTALLATION 5.1 Unpacking the Equipment The contents of your package are listed below. First, make sure that all the items in the kit have been included. If you find that any item is missing, contact your dealer immediately. 5.1.1. HomeLogiXTM Package Content • HomeLogiXTM unit • Transformer • Telephone cable • Backup battery • Button pack (provided separately) • Installation screw set 5.
INSTALLATION open collector outputs Active Low. GND Ground ZONE Wired Zone (zone 40) Alarm input. GND Ground TAMPER Wired Zone (zone 40) Tamper input. +15VDC VIN GND Input voltage from AC/DC adaptor VIN=13.8-15 . +13.8VDC (-) AUX (OUT) Auxiliary Power output (to power external devices) +13.8 VDC 500mA Load current Max. Current limited. LINE IN Telephone line in (from the wall to the system). HOME TEL Telephone line out (from system to telephone device).
INSTALLATION Both Aux 1 and Aux 2 have the same selection of programming. When programming the Aux 1 and Aux 2 open collector outputs, it is possible to select from several operational modes from the programming menu as described in the programming section under Automation sub section Set Triggers on page 35. 5.4.4. Wiring the ZONE 1 Wired Input: Wired input zone 40 for wired door detector.
INSTALLATION 5.5 Connect the AC Transformer Note: Complete all the wiring and programming before plugging the transformer in the AC outlet Attach the transformer and power up the system. The display shows the HomeLogiXTM logo and the current version. Plug in the transformer – the power LED on the control panel should light up. 5.6 Connecting to a Computer The control panel can be equipped with an optional MD-62 adaptor for serial data interchange with a computer. 5.7 Mounting the Back-plate 5.7.1.
INSTALLATION Figure 9: Back Plate When drilling the hole for the wires, it is recommended to drill the hole in the marked out area. Note: It is important to mount the back-plate first before connecting any of the wiring to the unit 5.7.2. Required Space The required space on the wall for the panel is (L) x (H). Hole size for wires: 2cm x 5cm. This is to be drilled according to the openings on the back-plate.
INSTALLATION 5.8 Dismounting the Control Panel Release HomeLogiXTM from the mounted back-plate by unlocking the locking hooks on the top of the back-plate by lifting them up and out of the recesses on top of the panel. Pull the top of the panel away from the wall to disconnect the connector to the back plate, and then remove the panel from the lower posts of the back-plate. 5.9 Replacing the Backup Battery To replace the backup battery: • Dismount the panel.
PROGRAMMING HOMELOGIXTM 6. PROGRAMMING HOMELOGIXTM 6.1 Overview We recommend that you program HomeLogiXTM before installing it. You can use the backup battery or the AC power supply for operating power while programming. Access the HomeLogiXTM installer’s menu by entering the default 4-digit installer’s code: 8888.
INSTALLERS MENU 7. INSTALLERS MENU The Installer’s menu enables access to the following group of options: • Change code • Zones • Enrolling • Security • Communications • Automation • Messages • Maintenance 7.1 Accessing the Installer Menu Press the Menu button twice to reach the INSTALLER MENU option and press Enter. Note: The default password for entering the Installer menu is “8888”.
INSTALLERS MENU 7.3 Zones Change ZONES Code Enrolling Security Communications Automation Messages Maintenance Zone #01-40 Zone Type Description Chime No activity This menu allows you to define each of the 40 available zones. You can define the zone type, description, activity type and it’s audible chime indication. To specify zones: The second sub menu is ZONES. Select the required zone by either browsing all 40 using the Menu button or by entering the zone number using the numeric keypad.
INSTALLERS MENU 7.4 Enrolling Change Zones ENROLLING Security Communications Automation Messages Maintenance Code Detectors Remote controls R. Sirens Keypads Repeaters The Third sub menu is ENROLLING. Browse the desired application listed below using the Menu button and access it by pressing the Enter button: • Detectors • Remote controls • Sirens • Keypads • Repeaters 7.4.1. Detectors You can enroll up to 39 detectors, one detector per zone, numbered 01 through 39. Zone no.
INSTALLERS MENU 7.4.2. Remote Controls You can enroll up to eight remote controls, and specify functions for each button on the remote control. You can also delete enrolled remote controls. To enroll a remote control and specify a function: Select the desired remote control number 01-08 by either browsing the remotes using the Menu button or by entering the remote number using the numeric keypad.
INSTALLERS MENU 7.4.4. Keypads You can enroll up to four keypads. You can choose to remove enrolled keypads.
INSTALLERS MENU Exit Delay Entry Delay Auto Arming Siren Time Siren Mode Relay Polarity Local Siren Supervision Time Jamming No Activity Time Trouble Beeps Bypass Option Quick Arm Panic Button Duress Code Alarm Cancel Alarm Abort Time Backlight Time Hide Display Key Beeps The fourth sub menu is SECURITY. Browse the desired security related setting, as described in detail ahead, using the Menu button, press the Enter button to access it. 7.5.1.
INSTALLERS MENU To modify the entry delay: Using the numeric keypad, specify the length of the entry delay between 1 and 99 seconds and press Enter to save your selection. 7.5.3. Auto Arming Auto Arming allows scheduled arming and disarming of the system for all weekdays at different hours. To activate auto arm: Using the Menu button, select the day of the week and press Enter to confirm.
INSTALLERS MENU To set the relay polarity: Using the Menu button, select one of the two options, N.O. or N.C., and press Enter to confirm. 7.5.7. Local Siren Specifies whether an activated alarm causes an internal siren (emitted from the system’s speaker) to sound or remain silent. The local siren is enabled by default. To set up a local siren: Using the Menu button, select one of the two options, Enable or Disable, and press Enter to confirm. 7.5.8.
INSTALLERS MENU Note: Required zones should be set to ‘Enabled’ for this security feature to work 7.5.11.
INSTALLERS MENU 7.5.14.Panic Button Enables the user to generate an alarm (audible or silent) by pressing the emergency button on the control panel, the remote control panic button will remain active at all times if enrolled. The local emergency button is disabled by default. To set a panic button: Using the Menu button, select one of the following options and press Enter to confirm: • Audible: to set an audible panic alarm that transmits a message to the CMS or private telephone set.
INSTALLERS MENU To set the alarm abort time: Using the numeric keypad, set the alarm abort time between 01 – 60 seconds, or set it to 00 to disable the option. 7.5.18.Backlight Time Specifies the backlight options; by default, the backlight time is set at 15 seconds. To set the backlight: Using the Menu button, select one of the following options and press Enter to confirm: • Always: to specify that the keypad and buttons are backlit at all times.
INSTALLERS MENU 7.6 Communications Change Zones Enrolling Security COMMUNICATIONS Automation Messages Maintenance Code System Telephone Private Report CS Report Setup Line Test AC Fail Report 2WV SETUP Fax Defeat Number of Rings The fifth sub menu is Communication, which deals with the setup of system communications parameters and settings with the outside world. Browse the desired communication related setting, as described in detail ahead, using the Menu button, press the Enter button to access it. 7.
INSTALLERS MENU • Report Options specifies the event groups that are included in a report. Using the Menu button, Enable or Disable a group, as required and press Enter to confirm: o Alarms (enabled by default) o Troubles (enabled by default) o Alerts o Bypass o Arm/disarm o Restore • Dialing Attempts specifies the number of times the system attempts to dial a private number before dialing the next specified private number.
INSTALLERS MENU Troubles (enabled by default) Alerts Bypass Arm/disarm Restore • CS Secondary specifies the secondary telephone number dialed and the secondary account code – the number that identifies your system to the second central station. The events reported are the events specified during setup. Follow the instructions in CS Primary • Protocol, specifies the reporting protocol used by the system to report events to the central stations. Currently only Contact ID is available.
INSTALLERS MENU selecting #1 (Listen), #3 (Talk), or #9 (Close communication) in the event the system calls when an alarm is sounded. The installer can set the following options: • CMS 2-way voice Enable/Disable • CMS 2-way voice Timeout However, if the KEY ON, TROUBLE, BYPASS, and MISC events are reported, and the CMS is in LISTEN-IN mode, the CMS receptionist can hear the alarm/emergency voice message events, if they belong to the same CMS.
INSTALLERS MENU 7.7 Automation Change Zones Enrolling Security Communications AUTOMATION Messages Maintenance Code Keypad Manual Set Triggers The sixth sub menu is Automation, which deals with the setup of various home automation options. Browse the desired automation related setting, as described in detail ahead, using the Menu button, press the Enter button to access it. 7.7.1.
INSTALLERS MENU 7.8 Messages Change Zones Enrolling Security Communications Automation MESSAGES Maintenance Code Keypad Mute House Name Custom Zones The seventh sub menu is Messages, which deals with custom text and voice zone descriptions, Personal messages between users and message mute options. Browse the desired setting, as described in detail ahead, using the Menu button, press the Enter button to access it. 7.8.1.
INSTALLERS MENU 5. Press ENTER TO LISTEN. This appears after the string of recordings have been entered. 6. Press Enter to stop the listening to one zone and move to the next zone. This option is circular. Note: Reset to factory settings does not delete these recordings. 7.
INSTALLERS MENU • Test Repeaters To view the results: For each of the tests, you can review the results by pressing the Enter button and then either the Menu button or the alphanumeric keys review all the units. To exit the RF test mode you must press the Quick (ESC) button 7.9.3. Test Indicators The indicators test checks the two indicator LED’s, power and status located on the Panel. To test the indicators: After entering this menu press Enter the LEDs will blink three times 7.9.4.
READING THE EVENT LOG 8. READING THE EVENT LOG The HomeLogiXTM event log stores up to 128 events. When the log is full, the new incoming event replaces the oldest event. Events are displayed in a chronological order, and include the date and time of their occurrence. To Access the Event Log: Access the event log by pressing 8 on the keypad when the system is in normal mode. To read an event, enter the master code and press Enter.
ACCESSORIES Annex I. ACCESSORIES I.1 HomeLogiXTM Compatible Detectors A wide assortment of wireless detectors is compatible with the HomeLogiXTM control panel, primarily for use in intrusion and personal safety applications. There are also other system components, such as RF repeaters for extending range, and wireless sirens for remote annunciation of alarms.
ACCESSORIES The sensor is housed in a dual tamper-detection, modernly designed housing. The sensor can be mounted to any rigid flat or corner surface to cover the desired volumetric space to be protected; a corner mount is available to enable corner tamper detection. When motion is detected, the PIR transmits a message to the control panel. If the control panel is armed, then the system will generate an alarm. Figure 13 PYR-2011 Wireless PIR Motion Detector I.1.3.
ACCESSORIES I.1.5. Universal Wire to RF (Two-Channel) Transmitter This special transmitter (Figure 5) was developed for interfacing with advanced sensors––such as microwave barriers, infrared barriers––fence perimeter protection detectors, and other third-party active detectors that produce a normally closed (NC) or normally opened (NO) output. The SA-25 has pulse counting on one of the inputs and can count 3, 6 or 9 pulses––programmable in that mode.
ACCESSORIES and for personal emergency applications. These transmitters can be enrolled onto the HomeLogiXTM. Note: For the model numbers shown below, XX identifies a particular frequency and country of application. Each detector is supplied with its own installation manual. All the wireless remote controls are powered with standard available AAA or M2 alkaline primary cells, which have long battery life and are easily replaced.
ACCESSORIES I.2.3. 1, 2 or 4-Button Remote Controls These hand-held transmitters (see Figure 9) come with a belt-clip attachment and a loop-clip attachment, so they can be hung on a wall or carried by the user on the belt, or car visor. The user arrives at the armed house and disarms the house by pressing a single button, without any need to be near the panel. Designed for comfortable use of the system, the transmitter can also fully arm (Away Arm) the panel, or partially arm zones (Home Arm).
SENSOR PLACEMENT and HELPFUL REFERENCE TABLES Annex II. SENSOR PLACEMENT and HELPFUL REFERENCE TABLES II.
SENSOR PLACEMENT and HELPFUL REFERENCE TABLES Zone No. Zone Type Description Chime Yes/No No Activity Zone PGM 1 PGM 2 Remarks 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40.
SENSOR PLACEMENT and HELPFUL REFERENCE TABLES II.4 Remote Control No. Holder Name Normal Operation PGM 1 PGM 2 Status Request 1. 2. 3. 4. 5. 6. 7. 8.
Reporting codesREPORTING CODES Annex III. REPORTING CODES III.1 Reporting codes The Table below provides a listing of the codes used to communicate with the CMS.
Reporting codesREPORTING CODESReporting codes Code Index 2D ---* Programmable Feature Description Periodic Test Report Event Listen in Follow - CID Code E602 E606 *This event is not sent by the panel to the dialer. Listen in Follow code is produced by the dialer according to current configuration: • 2-way voice enable/disable • 2-way voice period, Therefore there is no Index.
Limited WarrantyLIMITED WARRANTY Annex IV. LIMITED WARRANTY IV.1Limited Warranty ROSSLARE ENTERPRISES LIMITED S (Rosslare) TWO YEARS LIMITED WARRANTY is applicable worldwide. This warranty supersedes any other warranty. Rosslare's TWO YEARS LIMITED WARRANTY is subject to the following conditions: Warranty Warranty of Rosslare's products extends to the original purchaser (Customer) of the Rosslare product and is not transferable.
TECHNICAL SUPPORT Annex V. TECHNICAL SUPPORT Asia Pacific, Middle East, Africa Rosslare Security Products Headquarters 905-912 Wing Fat Industrial Bldg, 12 Wang Tai Road, Kowloon Bay Hong Kong Tel: +852 2795-5630 Fax: +852 2795-1508 E-mail: support.apac@rosslaresecurity.com United States and Canada 1600 Hart Court, Suite 103 Southlake, TX, USA 76092 Toll Free: +1-866-632-1101 Local: +1-817-305-0006 Fax: +1-817-305-0069 E-mail: support.na@rosslaresecurity.
0706-0960328+00 www.rosslaresecurity.
