RO- -UJEL.L. www.roswellmarine.com 11 6.5 Tower Speakers Installation & Usage Instructions Part# (920-1700 Information: info@roswellglobal.com If you have any questions please call : 1-321-638-1331 Rev.
Rl 6.5" Tower Speaker Installation Instructions www.roswellmarine .com ROSWf-L.L. Welcome to the family. Thank you for purchasing the best marine speakers in the world. After years of development and testing, we are proud to introduce the R1 Series marine speakers, built to outlast - and outperform - every other marine speaker on the market. We at Roswell started a revolution in the wakeboard industry back in 1998, and have since expanded into marine audio and other branches of the marine industry.
Rl 6.5" Tower Speaker Installation Instructions www.roswellmarine.com TOOLS & SUPPLIES NEEDED PACKAGE CONTENTS ~ ' ''' '' x2 (x2) (x2) I R1 6.5" Tower Speakers Wiring Harness Safety Lanyard x2 5/16" Allen Key 7/32" Allen Key Torque Wrench Utility Knife Heat Gun (x2) Wire Strippers &Crimps RED Phillips Screw Driver Measuring Tape Preparation Tower and boat Wiring (not included) • For safety, turn off the audio system and battery switch prior to beginning installation.
Rl 6.5" Tower Speaker Installation Instructions www.roswellmarine.com Wiring options for RGB LEDs Before starting assembly you will need to consider the LED configuration you would like to use .. You can wire the RGB LEDs in your speakers to be either one fixed color, or your can wire them to be used with the Roswell RGB Controller {Part Num. C920-1620). Connecting the wires on the speaker wiring harness in different configurations will produce different colors.
R16.5" Tower Speaker Installation Instructions www.roswellmarine.com 1) Use wire strippers to expose 1/4" of wire on all wires. 2) Connect the tower wires to the speaker wiring harness according to the LED configuration you plan to use. 3) Heat shrink the connectors. 4) Carefully push the wires back into the tubing. < a~ x2 x12 ~ orx8 I -----------·- Speaker Harness -------------· Deutsch Connector \ Determine your mounting location on your tower.
Rl 6.5" Tower Speaker Installation Instructions www.roswellmarine.co:n 1. Remove the two 3/8n-16 bolts from the clamp top. 2. Remove the two plastic clamp inserts from the clamp. 3. Remove the four 3/8"-16 bolts from inside the speaker can. 3. 1. r 5/16" 1. Rotate the clamp body to the angle required for your installation. 2. Re-install the 3/8"-16 bolts through the internal spacer, can, outer spacer, plastic spacer and into the clamp angle insert with red threadlock and tighten to 25ft-lbs. 1.
Rl 6.5" Tower Speaker Installation Instructions www.roswellmarine.com Measure the tubing you will be mounting your speakers to and select the appropriate plastic insert for your tubing diameter. Place your plastic insert into the clamp. Locate speakers in desired location. Apply red threalock and tighten clamp bolts to 30ft-lbs. 1. Loop the safety lanyard over the tower next to the speaker clamp and feed one end of the lanyard through the other end. 2.
Rl 6.5" Tower Speaker Installation Instructions www.roswellmarine.com Plug in both speakers. Install the 5/8"-11 clamp set screws with red thread lock to secure the clamps into place. 3"tubes use the 1/2" long set screw. Tubes smaller than 3.0" use the 13/1 6" long set screw. Note: This set screw will leave a mark on your tower when it is tightened. .
Rl 6.5" Tower Speaker Installation Instructions www.roswellmarine.com Roswell L1m1ted Warranty Roswell warrants all new Rl Series Tower Speakers against defeds in material and workmanship for a period ofTWO (2) YEARS from the original date of purchase. This warranty is not transferable and applies only to the original retail purchaser from an authorized Roswell retailer.
