Owners Manual

16
DT-6000 DAC Transport
Troubleshooting
Most difculties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the area of the
difculty, check the control settings, determine the cause of the fault and
make the necessary changes. If you are unable to get sound from the unit,
refer to the suggestions for the following conditions:
Power Indicator Is Not Illuminated
The Power Indicator and the basic items in the display window should be
illuminated whenever the unit is plugged into the wall power outlet and the
Power button is pushed in. If it does not light, test the power outlet with
another electrical device, such as a lamp. Be sure the power outlet being
used is not controlled by a switch that has been turned off.
Fuse Replacement
If another electrical device works when plugged into the power outlet,
but the Power Indicator and the display still will not light when the unit is
plugged into the wall outlet, it indicates that the internal power fuse may
have blown. If you believe this has happened, contact your authorized Rotel
dealer to get the fuse replaced.
No Sound
Check the cables between the unit and the amplier inputs to be sure they
are connected properly. Be sure the correct amplier input is selected. Be
sure the tape monitor system of the amplier has not been activated. Check
the wiring between the amplier and the speakers.
Playable Audio Formats
PC-USB
Format Notes
Format determined
by the Media Player/
Server software that
you use.
Any supported format by the PC software
PCM Audio:
44.1k, 48k, 88.2k, 96k, 176.4k, 192k, 384k
(16 bit, 24 bit and 32 bit)
DSD64, DSD128 and DSD256
MQA, MQA Studio (24 bit / 384k)
Roon Tested
Coax/Optical
Format Notes
SPDIF LPCM
44.1k, 48k, 88.2k, 96k, 176.4k, 192k
16 bit, 24 bit
Specications
Total Harmonic Distortion + NoiseTotal Harmonic Distortion + Noise
Optical/Coaxical Input < 0.0007%
CD/PC-USB Input < 0.0012%
Intermodulation DistortionIntermodulation Distortion < 0.0012%
Frequency ResponseFrequency Response 20 Hz - 20k Hz，+0, -0.15dB
10 Hz - 70kHz, +0, -3dB
Channel BalanceChannel Balance ± 0.5 dB
Channel SeparationChannel Separation > 115 dB @ 10k Hz
Signal to Noise RatioSignal to Noise Ratio (A Weighting) > 115 dB
Dynamic RangeDynamic Range > 99 dB
Input Sensitivity Input Sensitivity 0dBfs / 75 Ohms
Digital to Analog ConvertersDigital to Analog Converters ESS 32-Bit/768kHz DAC
Analog Output Level / Impedance Analog Output Level / Impedance (0dBfs)
Unbalanced (RCA) 2.1 V / 10 Ohms
Balanced (XLR) 4.3 V / 20 Ohms
Decodable Coaxial/Optical Digital SignalsDecodable Coaxial/Optical Digital Signals SPDIF LPCM (up to 192k Hz 24 bit)
Decodable PC-USB Digital Input SignalsDecodable PC-USB Digital Input Signals USB Audio Class 2.0
(up to 384kHz 32bit)
*Driver installation required*
Support native DSD (up to 11.2M) and
DoP
Support MQA and MQA Studio
(up to 24 bits/384kHz)
Roon Tested.
Power RequirementsPower Requirements
USA 120V, 60 Hz
EC 230V, 50 Hz
Power ConsumptionPower Consumption 25 Watts
Standby Power ConsumptionStandby Power Consumption < 0.5 Watts
Dimensions Dimensions (W x H x D) 431 x 104 x 320 mm
17 x 4 x 12
3
/5 ins
Front Panel HeightFront Panel Height 2U / 3
1
/2 ins / 88.1 mm
WeightWeight (net) 8.11 kg, 17.88 lbs.
All specifications are accurate at the time of printing. Rotel reserves the right to make
improvements without notice.
Rotel and the Rotel HiFi logo are registered trademarks of The Rotel Co, Ltd., Tokyo, Japan.
‘MQA’ or ‘MQA.’ indicates that the product is decoding and playing an
MQA stream or le, and denotes provenance to ensure that the sound is
identical to that of the source material. ‘MQA.’ indicates it is playing an
MQA Studio le, which has either been approved in the studio by the
artist/producer or has been veried by the copyright owner.
‘OFS’ conrms that the product is receiving an MQA stream or le. This
delivers the nal unfold of the MQA le and displays the original sample
rate.