Owners Manual

15
English
NOTE: It is recommended to Reset Factory Defaults after the software
update is complete.
• PC-USB: This shows current loaded software version for PC-USB processor.
• SIGNAL SENSE: Check if an audio signal is present on the congured
Signal Sense input. The RC-1572MKII monitors the data stream to
determine if there is audio. If there is no audio detected for 10 minutes,
the RC-1572MKII will enter Signal Sense Power Mode. When in Signal
Sense Power Mode and the RC-1572MKII detects audio on Signal Sense
input, the unit will automatically power on. To disable this function, select
the OFF option which is the factory default setting.
NOTE: When the SIGNAL SENSE function is activated, the RC-1572MKII
will consume additional power in signal sense standby mode.
NOTE: Due to local power consumption regulations the SIGNAL SENSE
function is not available in all markets.
• FACTORY DEFAULT: This sets the unit back to the original state as when
it left the factory. Press the + button on the front panel or the Right button
on the remote control to select <YES> then press the ENTER button on the
front panel or the ENT button on the remote control.
NOTE: All previously configured options will be erased and reset to
the factory default settings.
Troubleshooting
Most difculties in audio systems are the result of incorrect connections,
or improper control settings. If you encounter problems, isolate the area
of the difculty, check the control settings, determine the cause of the fault
and make the necessary changes. If you are unable to get sound from the
RC-1572MKII, refer to the suggestions for the following conditions:
Power Indicator Is Not Illuminated
The Power Indicator ring around the power button and the basic items in
the Display window should be illuminated whenever the RC-1572MKII is
plugged into the wall power outlet and the POWER switch is pushed in. If
it does not illuminated, test the power outlet with another electrical device,
such as a lamp. Be sure the power outlet being used is not controlled by a
switch that has been turned off.
Fuse Replacement
If another electrical device works when plugged into the power outlet,
but the Power Indicator still will not illuminated when the RC-1572MKII is
plugged into the wall outlet, it indicates that the internal power fuse may
have blown. If you believe this has happened, contact your authorized Rotel
dealer to get the fuse replaced.
No Sound
Check the signal source to see if it is functioning properly. Make sure the
cables from the signal source to the RC-1572MKII inputs are connected
properly. Check all the wiring between the RC-1572MKII and the power
amplier, and the speakers.
Cannot Connect via Bluetooth
If you cannot pair your Bluetooth enabled device to the RC-1572MKII, delete
the memory of the previous connection on the RC-1572MKII and on your
device. On your device this is often listed as “Forget this Device”. Then try
to make the connection again.
Playable Audio Format
USB Apple (iPhone, iPod, iPad)
Format Notes
Any supported le
loaded to Apple
device.
Any supported le loaded to Apple device. Phone may
resample depending on stored format. May exclude
Apps designed to play formats not originally supported
by the sending device.
APTX and AAC Bluetooth
Format Notes
Any format supported
by the sending device.
May exclude Apps designed to play formats not originally
supported by the sending device.
PC-USB
Format Notes
Format determined
by the Media Player/
Server software that
you use.
Any supported format by the PC software:
PCM Audio:
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz, 384 kHz
16 Bit, 24 Bit, 32 Bit
MQA, MQA Studio (24 Bit / 384 kHz)
Roon Tested
Coax/Optical
Format Notes
SPDIF LPCM
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz
16 Bit, 24 Bit