Operation Manual

44
RSP-1572 SURROUND SOUND PROCESSOR
screen will appear, please select YES. The unit will power off (to Standby
Mode) and then on, with the factory settings restored. To return to the
MAIN menu without resetting the FACTORY DEFAULT settings, change
the entry to NO and press the ENT button.
Note: Resetting to factory default settings will erase all stored settings
including delay settings, speaker settings, balance settings, input settings
and more. You will lose ALL system configuration settings. Be certain
that you wish to do so before resetting the factory defaults. If you have
memorized a USER DEFAULT setting, this will be retained even after
factory default.
To memorize USER DEFAULT settings: Many of the current configuration
settings can be stored as a USER DEFAULT, which can be activated at
any time from this menu screen. To save the current settings as a USER
DEFAULT:
Place the highlight on the SET USER DEFAULT line using the Up/1.
Down buttons and use the Left/Right buttons to change the setting
to YES.
Press the ENT button on the remote to go to confirmation screen 2.
where a password must be entered. The default password is 0000.
If the entered password is correct, the current settings will be saved
as the new USER DEFAULT settings.
To return to the MAIN menu without saving changes, change all 3.
entries on the screen to NO and press ENT.
Note: If there is insufficient memory to store a USER DEFAULT
configuration file, the SET USER DEFAULT option will not be available.
To activate memorized USER DEFAULT settings: After you have stored a
USER DEFAULT configuration file, you can activate those settings at any
time by placing the highlight on the USER DEFAULT line using the Up/
Down buttons. Use the Left/Right buttons to change the setting to YES.
Press the ENT button on the remote to proceed with activating the USER
DEFAULT settings.
To return to the MAIN menu without activating the USER DEFAULT settings,
change the entry to NO and press the ENT button.
To change the password: The password programmed at the factory is
0000. If you wish to change the password:
Place the highlight on the SET NEW PASSWORD line using the 1.
Up/Down buttons. Use the Left/Right buttons to change the setting
to YES. Press the ENT button on the remote to proceed to the
PASSWORD screen.
Enter the four digits of the old password by pressing the Left/Right 2.
buttons to select the first letter of the new password, then pressing
ENT to move to the second character. Repeat until the old password
is entered. Successful entry of the old password will jump to the
ENTER NEW PASSWORD line.
Enter the four digits of the new password by pressing the Left/Right 3.
buttons to select the first letter of the new password, then pressing
ENT on the remote to move to the second character. Repeat until
the new password is entered.
You will be asked to re-enter the password again on the CONFIRM 4.
PASSWORD line, following the same procedure. Once the password
is successfully confirmed, it will be saved and you will return to the
DEFAULT SETUP MENU automatically.
To exit the PASSWORD screen without changing the password, 5.
highlight the DEFAULT SETUP MENU line and press ENT to return
to the previous screen.
Note: The factory password is 0000. A default password that will always
be recognized is 8888.
EQ Setup
E Q O P T I O N S
E Q E N A B L E : O f f
S P E A K E R : A L L
E Q V A L U E : E n t e r
M A I N M E N U
The EQ Setup menu provides access to three functions:
EQ ENABLE: Select either ON or OFF to turn on/off the EQ feature.
SPEAKER: Select either ALL or Individual speakers using Left/Right
keys.
EQ VALUE: This menu allows you to enter the EQ value. There are total
10 bands as below.
E Q V A L U E S E T
S P E A K E R A L L S P E A K E R
- - - - - - - - 1 - - - - 2 - - - - 3 - - - - - 4 - - - - - 5 -
F r e q : 4 0 6 0 1 0 0 1 2 0 1 6 0
Q : 2 2 2 2 2
G a i n : 0 0 0 0 0
- - - - - - - - 6 - - - - 7 - - - - 8 - - - - - 9 - - - - 1 0 -
F r e q : 1 3 0 0 1 7 5 0 4 K 1 0 K 1 6 K
Q : 2 2 2 2 2
G a i n : 0 0 0 0 0
E Q S E T U P M E N U
:
BAND 1 Freq : 20Hz - 80Hz, 1Hz Step Default 40 Hz
BAND 2 Freq: 20Hz - 80Hz, 1Hz Step Default 60 Hz
BAND 3 Freq: 81Hz - 140Hz, 1Hz Step Default 100 Hz
BAND 4 Freq: 81Hz - 140Hz, 1Hz Step Default 120 Hz
BAND 5 Freq: 141Hz - 200Hz, 1Hz Step Default 160 Hz
BAND 6 Freq: 1110Hz - 1550 Hz, 10Hz Step Default 1300 Hz
BAND 7 Freq: 1560Hz - 2000 Hz, 10Hz Step Default 1750 Hz
BAND 8 Freq: 2.1kHz - 8kHz, 100Hz Step Default 4k Hz
BAND 9 Freq: 8.1kHz - 14kHz, 100Hz Step Default 10k Hz
BAND 10 Freq: 14.1kHz - 20kHz, 100Hz Step Default 16k Hz
Q : 1 - 24
Gain : -12dB - 0 - +3dB
Note: Q in EQ value relates to the bandwidth of the filter. The higher
the value, the narrower the bandwidth.