Owners Manual

15
NOTE: The DISPLAY button is common for all Michi models. To Dim or
enable the display PUSH or PUSH-HOLD the button and point to the Michi
products. If a unit does not respond to a DISPLAY command simply send
the command again using a PUSH or PUSH-HOLD.
AUDIO H: The AUDIO button allows temporary adjustments to the Balance,
Bass and Treble settings. To change these settings push the AUDIO button
on the remote control and navigate to the desired setting using the
T
/
D
button and push the Enter
K
button. Use the
T
/
D
button to change the
value. Push the AUDIO button again to exit the menu or to exit the Audio menu.
NOTE A properly setup Hi-fi system should not require changes to the
Bass or Treble setting. Use these adjustments sparingly.
NOTE These settings are temporary and not saved when the amplifier
is powered off to Standby. For permanent changes, configure the audio
settings in the setup menu.
Button
E
: Push the button once to mute the audio. An indication
appears in the front panel on-screen display. Press the button again to restore
the previous volume level.
VOLUME Knob 3 and VOL +/- Buttons
F
: The VOLUME +/- buttons on the
remote and the rotary control on the front panel provide the master VOLUME
control, adjusting the output level.
Main Menu
SOURCE
SETUP
NETWORK
AUDIO
DISPLAY
SYSTEM
The Setup menu provides access to OSD screens for various configuration
options. Setup menu is reached by pressing the SETUP
B
button on the
remote. To select the desired menu, move the highlight using the
T
/
D
arrow buttons and press the Enter
K
button on the remote control. Press the
SETUP
B
button again to return to the previous menu or select “EXIT“ on the
OSD to end setup and return to normal operation.
Source Configuration
Coax 2
Coax 3
OPT 1
OPT 2
SOURCE
SETUP
Name
Enabled
Volume
Input
Coax 1
Audio Mode
A key step in setting up the unit, is to configure each source input using the
Source Setup screens. Configuring the inputs allows you to set defaults for a
number of settings including the type of input connector, the desired audio
mode, custom labels that appear in the displays when a source is selected,
and many more options.
This Source menu in the Setup menu, provides the following options, selected
by placing the highlight on the desired line using the
T
/
D
arrow buttons
and pressing the Enter
K
button. This action displays the right side options
allowing changes. Change the options using the
T
/
D
arrow buttons and
press the Enter
K
button to confirm.
INPUT: Changing this input allows you to select a specific input for configuring.
(COAX , OPT , PCUSB, BLUETOOTH, COMPACT DISC, PHONO, TUNER,
AUX , XLR)
NAME: The name of the source can be customized. For example Aux 1 can be
named “TV” for easier reference. The default NAME is the same as the SOURCE.
Place the highlight on this option and use the
T
/
D
arrow buttons on the
remote control to select “Custom” then press the Enter
K
button to enter
the source name edit sub menu as below.
DONE
0 1 2
8 9 A
H I J
B
Q R S T
Z
K L M N
U V W X
C D E F
3 4 5 6
O
7
G
P
Y
-
SOURCE
SETUP
Enabled
Volume
Audio Mode
Name
Bass
Input
1. Press the
T
/
D
arrow buttons on the remote control to change the first
letter, scrolling through the list of available characters.
2. Press the Enter
K
button on the remote control to confirm that letter and
move to the next position.
3. Repeat steps 1 and 2 until all ten characters have been completed. The final
press of the Enter
K
button saves the new name. You can select the “DONE“
button on the OSD to confirm if you have less than ten characters to enter.
Enabled: Allows a source input to be enabled and appear in the list of source
input options when using the source selection on the front panel or IR remote
control. Unused sources should be set to disabled by selecting the “No” option.
Options include: Yes(Default), No.
Volume: Configures a Fixed Volume level for a specified input. This volume
level is immediately set when this source input is selected and cannot be
changed using the front panel or IR remote. This is useful for input sources
that include their own volume setting like common Apps on phones or tablets.
Options include: Variable (Default), 30 - 90.
Audio Mode: Configures audio mode to Direct Bypass or Tone Enabled.
Options include: Direct Bypass (Default), Tone Enabled.