Manual

Assembly instruction for fastening set art. no.: FF35121brickwork
1 2 3
- Drilling hole
- Carefully clean the drill dust from the
borehole
Tel. + 49 (0) 61 95 / 800 - 1 · Fax + 49 (0) 61 95 / 7 44 22 · [e-mail] · www.rothenberger.com
ROTHENBERGER Werkzeuge GmbH · Industriestraße 7 · D-65779 Kelkheim/Germany
06.10/F&E
Ø20mm
85mm
M12
When tightening the nut the cone into the anchor shells
drawn and spreads apart these and wedged itself.
Do not use worn out ankers! !
Attention! !
If any damage on the anker, replace with new one
Every time before start of operation make sure that the machine is firmly fastened and not able to shake
- Fit in brickwork dowel
- Screw the d with washer and
mounted nut into the anker
iamond knurl threaded bar
-
-
Attach mounting plate of drill rig
Enclose washer and screw on with wing nut
M12
Assembly instruction for fastening set art. no.: FF35121brickwork
Assembly instruction for fastening set art. no.: FF35121brickwork
Assembly instruction for fastening set art. no.: FF35121brickwork
1
1
1
2
2
2
3
3
3
- Drilling hole
- Carefully clean the drill dust from the
borehole
- Drilling hole
- Carefully clean the drill dust from the
borehole
- Drilling hole
- Carefully clean the drill dust from the
borehole
Tel. + 49 (0) 61 95 / 800 - 1 · Fax + 49 (0) 61 95 / 7 44 22 · [e-mail] · www.rothenberger.com
Tel. + 49 (0) 61 95 / 800 - 1 · Fax + 49 (0) 61 95 / 7 44 22 · [e-mail] · www.rothenberger.com
Tel. + 49 (0) 61 95 / 800 - 1 · Fax + 49 (0) 61 95 / 7 44 22 · [e-mail] · www.rothenberger.com
ROTHENBERGER Werkzeuge GmbH · Industriestraße 7 · D-65779 Kelkheim/Germany
ROTHENBERGER Werkzeuge GmbH · Industriestraße 7 · D-65779 Kelkheim/Germany
ROTHENBERGER Werkzeuge GmbH · Industriestraße 7 · D-65779 Kelkheim/Germany
06.10/F&E06.10/F&E06.10/F&E
Ø20mmØ20mmØ20mm
85mm
85mm
85mm
M12
M12
M12
When tightening the nut the cone into the anchor shells
drawn and spreads apart these and wedged itself.
When tightening the nut the cone into the anchor shells
drawn and spreads apart these and wedged itself.
When tightening the nut the cone into the anchor shells
drawn and spreads apart these and wedged itself.
Do not use worn out ankers! !
Attention! !
If any damage on the anker, replace with new one
Every time before start of operation make sure that the machine is firmly fastened and not able to shake
Do not use worn out ankers! !
Attention! !
If any damage on the anker, replace with new one
Every time before start of operation make sure that the machine is firmly fastened and not able to shake
Do not use worn out ankers! !
Attention! !
If any damage on the anker, replace with new one
Every time before start of operation make sure that the machine is firmly fastened and not able to shake
- Fit in brickwork dowel
- Screw the d with washer and
mounted nut into the anker
iamond knurl threaded bar
- Fit in brickwork dowel
- Screw the d with washer and
mounted nut into the anker
iamond knurl threaded bar
- Fit in brickwork dowel
- Screw the d with washer and
mounted nut into the anker
iamond knurl threaded bar
-
-
Attach mounting plate of drill rig
Enclose washer and screw on with wing nut
-
-
Attach mounting plate of drill rig
Enclose washer and screw on with wing nut
-
-
Attach mounting plate of drill rig
Enclose washer and screw on with wing nut
M12
M12
M12