Use and Care Guide

%1>B5/1
#>1B1:@5B19-5:@1:-:/1
<1>2;>910.EA:-A@4;>5F10
<1>?;::189-E>1?A8@5:95?<8-/5:3;2
5:@1>:-8C5>1?-:0/;9<;:1:@?C45/4/;A80
/-A?1?1>5;A?4-F->0 We recommend that
all tool service be performed by a Bosch or
Rotozip Factory Service Center or Authorized
Bosch Service Station. Call 1-877-ROTOZIP
(1-877-768-6947) if your tool needs service.
&""'$&"!
Your Rotozip tool has been properly lubricated
and is ready to use. The lubrication applied at
the factory lasts for the life of the tool.
$"!$'%%
The brushes and commutator in your tool have
been engineered for many hours of
dependable service. To maintain peak
efficiency of the motor, we recommend every
two to six months the brush es be examined.
Only genuine Rotozip replace ment brushes
specially designed for your tool should be
used.
$!%
Your Rotozip tool and attachments contain
sealed bearings designed to last the life of the
tool. Bearings which become noisy (due to
heavy load or very abrasive material cutting)
should be inspected at once to avoid
overheating or motor failure. Contact your local
Bosch or Rotozip Factory Service Center if
your bearings become noisy.
81-:5:3
&;-B;50-//501:@?-8C-E?
05?/;::1/@@41@;;82>;9
@41 <;C1> ?A<<8E .12;>1 /81-:5:3 ;>
<1>2;>95:3-:E9-5:@1:-:/1 The tool may
be cleaned most effectively with compressed
dry air. 8C-E?C1->?-21@E3;3381?C41:
/81-:5:3@;;8?C5@4/;9<>1??10-5>
Ventilation openings and switch levers must be
kept clean and free of foreign matter. Do not
at tempt to clean by inserting pointed objects
through openings.
1>@-5:/81-:5:3-31:@?
-:0 ?;8B1:@? 0-9-31
<8-?@5/<->@? Some of these are: gasoline,
carbon tetrachlo ride, chlo rinated cleaning
solvents, ammonia and house hold detergents
that contain ammonia.
!
WARNING
-5:@1:-:/1
!
WARNING
!
CAUTION
-23-
2-:1D@1:?5;:/;>05?
:1/1??->E -/;>0 C5@4
-01=A-@1?5F1/;:0A/@;>?@4-@5?/-<-.81
;2/->>E5:3@41/A>>1:@:1/1??->E2;>E;A>
@;;8 9A?@ .1 A?10 This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-
wire extension cords that have 3-prong plugs
and receptacles.
!"& The smaller the gauge number, the
heav i er the cord.
$" !%,%"*&!%"!"$%
("&&$!&!'$$!&&""%
!
WARNING
&;;8K?
9<1>1
$-@5:3
;>0%5F15:)
)5>1%5F1?5:99

3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 —— ————
25 50 100 150 15 30 60 120
;>01:3@45:11@ ;>01:3@45: 1@1>?
D@1:?5;:;>0?
RZ 2610021432 10-12_RZ 2610021432 10-12.qxp 10/30/12 9:57 AM Page 23