Use and Care Guide

-6-
!1B1>4;80@41C;>7<51/15:;:14-:0-:0
@41@;;85:@41;@41>4-:0C41:5:A?1
!1B1><8-/14-:0?:1->;>.18;C/A@@5:3
?A>2-/1 Clamping the material and guiding
the tool with both hands is safer.
!1B1> 8-E C;>7<51/1 ;: @;< ;2 4->0
?A>2-/1? 8571 /;:/>1@1 ?@;:1 1@/
Protruding cutting bit may cause tool to jump.
8C-E?C1->?-21@E3;3381?-:00A?@
9-?7'?1;:8E5:C188B1:@58-@10->1-
Using personal safety devices and working in
safe environment reduces risk of injury.
2@1>/4-:35:3@41.5@?;>9-75:3-:E
-06A?@91:@?9-71?A>1@41/;881@:A@-:0
-:E;@41>-06A?@91:@01B5/1?->1?1/A>18E
@534@1:10 Loose adjustment device can
unexpectedly shift, causing loss of control,
loose rotating components will be violently
thrown.
!1B1>?@->@@41@;;8C41:@41.5@5?1:3-310
5:@419-@1>5-8 The bit cutting edge may grab
the material causing loss of control of the
cutter.
8C-E?4;80@41@;;8C5@4@C;4-:0?0A>5:3
?@->@A<. The reaction torque of the motor can
cause the tool to twist.
)41:>;A@5:3;>/A@@5:3@4105>1/@5;:;2
2110C5@4@41.5@K?/A@@5:310315:@;@41
9-@1>5-85?B1>E59<;>@-:@8C-E?2110@41
.5@5:@;@419-@1>5-85:@41?-9105>1/@5;:
-?@41/A@@5:310315?1D5@5:32>;9@41
9-@1>5-8When viewing the tool from the top,
the bit rotates clockwise. If the tool is between
the workpiece and your body, then feed the
tool to your right. If the workpiece is between
the tool and your body, then feed the tool to
your left. Feeding the tool in the wrong
direction causes the cutting edge of the bit to
climb out of the work and pull the tool in the
direction of this feed.
!1B1>A?10A88;>0-9-310.5@?%4-><.5@?
9A?@.14-:0810C5@4/->1 Damaged bits
can snap during use. Dull bits require more
force to push the tool, possibly causing the bit
to break.
!1B1>@;A/4@41.5@0A>5:3;>599105-@18E
-2@1>@41A?1 After use the bit is too hot to be
touched by bare hands.
!1B1>8-E@41@;;80;C:A:@58@419;@;>4-?
/;91@;-/;9<81@1?@-:0?@588 The spinning
bit can grab the surface and pull the tool out of
your control.
!1B1>A?1.5@?@4-@4-B1-/A@@5:305-91@1>
3>1-@1>@4-:@41;<1:5:35:@41.-?1
;:;@A?1@41@;;82;>0>5885:3<A><;?1?
This tool is not intended to be used with drill
bits.
8C-E?A?1@41@;;8C5@4@4101<@43A501
?1/A>18E-@@-/410-:0<;?5@5;:1028-@
-3-5:?@9-@1>5-8.15:3/A@ The guide
securely positioned on the material improves
the stability and control of your tool.
)41:/;::1/@5:3@;;8@;0A?@/;881/@5;:
-:01D@>-/@5;:?E?@19?.1?A>1@41?1->1
/;::1/@10-:0A?10-//;>05:3@;@;;8-:0
B-/AA95:?@>A/@5;:?Proper use of dust
collection can reduce dust related hazards.
)41:A?5:3@;;8C5@40A?@/;881/@5;:-:0
1D@>-/@5;: ?E?@19? 19<@E @41 0A?@
/;:@-5:1> .12;>1 .135::5:3 C;>7
2>1=A1:@8E0A>5:3C;>7-2@1>/;9<81@5;:;2
C;>7-:0.12;>1?@;>5:3@41@;;8Be
extremely careful of dust disposal, materials in
fine particle form may be explosive.
;:;@@4>;C0A?@;:-:;<1:25>1Fine
dust particles may burn explosively.
)41:<1>2;>95:3?-:05:3-:0?A>2-/1
<>1<->-@5;:;<1>-@5;:?C5@4@;;8/;::1/@10
@;-0A?@/;881/@5;:-:01D@>-/@5;:?E?@19
.1-C->1;2@419-@1>5-8?/>1-@5:3@410A?@
Combustion from mixture of varnishes,
lacquers, polyurethane, oil or water with dust
particles can occur if there is a static
discharge, electric spark, or excessive heat
causing a fire in the dust collection and
extraction system.
;:;@A?10A?@1D@>-/@5;:2;>;<1>-@5;:?
@4-@ 5:/8A01 .A>:5:3 ?9;75:3 ;>
?9;801>5:35@19?85714;@-?41?;>?<->7?
Fire inside the vacuum tank or bag may occur.
Dust may smolder and set vacuum on fire
long after work is completed.
BIT
WORK
DIRECTION OF
FEED
START
HERE
RZ 2610021432 10-12_RZ 2610021432 10-12.qxp 10/30/12 9:57 AM Page 6