Manual

ManualsBrandsRough Country ManualsCar1058

TJ, YJ WINCH PLATE & BUMPER COVER

Thank you for choosing Rough Country

Please read instructions before beginning installation. Check the kit hardware against the parts list and product

layout. Be sure you have all needed parts and know where they go. Also please review tools needed list and

make sure you have needed tools.

If questions exist we will be happy to answer any questions concerning the design, function, and correct use of

this product.

The installer must verify that the mounting kit does not interfere with the factory air bag sensors, which must not

be relocated or modified in any way. The vehicles are bag system may not operate properly if the winch mount-

ing kit is not mounted in compliance with the vehicle manufacturers recommendations.

Winch mounting should only be performed on vehicles with standard OEM bumpers.

INSTALLATION

1. Place vehicle on a flat surface and set emergency brake.

2. Remove the front valence (sway bar cover), using a 3/8” wrench. See PHOTO 1

3. Using a T55 torx socket, remove the front bumper mounting hardware and tow hooks if equipped.

4. Using a 15mm socket remove the front stabilizer mounting bolts. (TJ ONLY)

5. If installing a winch at this time it is recommended that you install the winch to the mounting plate, before

installing the plate on the vehicle.

6. Place the supplied washers as shown in PHOTO 2 on TJ models. YJ models will not use these washers.

Kit Contents:

1– Mounting Plate

1– 1012Bag2 including:

4– Large Thick Washers

4- 1/2” x 1 1/2” Bolt

4– 1/2” Flat Washers

12-1/2” x 1 1/2” Button

Head Bolts

4-1/2” Lock Nuts

2-10mm x 40mm Bolts

2-10mm Flat Washers

2-3/8” X 1 1/4” Bolts

2-3/8” Lock nuts

Tools Needed:

T55 Torx bit

3/8” Wrench

17mm Socket

3/4” Wrench

8mm Allen Wrench / Bit

92101200

PHOTO 1

REMOVE THE SWAY BAR COVER ON TJ

PHOTO 2

PLACE WASHERS ON FRAME (TJ SHOWN)

Optional

Accessories:

Light Bar- #1014

Stinger #1013

D-Ring Mount-#1058

Summary of content (4 pages)

PAGE 1
92101200 TJ, YJ WINCH PLATE & BUMPER COVER Thank you for choosing Rough Country Please read instructions before beginning installation. Check the kit hardware against the parts list and product layout. Be sure you have all needed parts and know where they go. Also please review tools needed list and make sure you have needed tools. If questions exist we will be happy to answer any questions concerning the design, function, and correct use of this product.
PAGE 2
7. Place winch mounting plate in position and align the mounting holes on the plate with the holes on the frame. See PHOTO 3. 8. Install the supplied bumper brackets as shown on the winch plate. See PHOTO 4. PHOTO 3 PLACE THE WINCH PLATE ON FRAME PHOTO 4 PLACE THE FRAME BRACKET ON PLATE 9. Place the upper bracket on the lower bracket. See Photo 5. 10. Install the bracket using the supplied 10mm x 40mm bolts / washers (TJ only) in the rear holes and the 1/2” x 1 1/2” bolts / washers as shown in Photo 6.
PAGE 3
TJ SWAY BAR COVER TRIMMING 1. On the TJ the front sway bar cover can be replaced with some trimming, if you elect to keep the cover see PHOTO 1 and 2 for required cutting. 2. Trim the cover as shown below and replace, using a 3/8” wrench. PHOTO 1 PHOTO 2 BUMPER SHOWN WITH STINGER BUMPER SHOWN WITH LIGHT BAR POST INSTALLATION INSTRUCTIONS 1. Check and retighten wheels at 50 miles and again at 500 miles. Periodically check all hardware for tightness. 2. Always practice safe winch operation.
PAGE 4
ROUGH COUNTRY ELECTRIC WINCH AVAILABLE IN 9500LB & 12000LB PART # 1013 STINGER KIT PART # 1056 D-RING KIT PART # RS110 SYNTHETIC ROPE PART # 1014 LIGHT BAR/ WINCH GUARD PART # RS120 WINCH EXTENSION STRAP THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR OFF ROAD NEEDS.