Vehicle Application: Installation Instructions Trektop NX • Jeep Wrangler TJ 1997 – 2006 Part Number: 56820 www.Bestop.com - We’re here to help! Visit our web site and click on “Ask a Question”. Click here for more Jeep® Accessories by Bestop.
Trektop NX Installation Instructions Parts List and Hardware Identification Fabric Top Quarter Window, Right Quarter Window, Left Rear Window Qty - 1 Qty - 1 Qty - 1 Qty - 1 #8 x 1/2" Pan Head Washer Screw - Black, Qty - 4, Part Number 200.48 Install Door Surrounds Remove the hard top. If your vehicle has molded seals on the belt rail, remove them by pulling up on the plastic rivet. #8 x 5/8" Pan Head Screw, Qty - 8, Part Number 278.13 Locate the left and right Door Surrounds.
Trektop NX Installation Instructions Orient Tailgate Mounts Assemble Side Bows to Header Locate the left and right Tailgate Mounts. Place the holes in the mounts over the dimples in the vehicle body. Mark the hole locations. Lay the Header upside down. Match the holes in the Side Bows with the holes in the Header. Orient the so the knobs point inward. Slide the Bows over the pins on each side of the Header. Use two (2) #12 x 3/8" Pan Head Zinc Screws to secure each Side Bow to the Header.
Trektop NX Installation Instructions Mount Header Assembly to Door Surround Install Top Fabric on Header Lay the top fabric, backing side up and aligned with the front edge of the Header. Use a utility knife to slit the fabric over each screw position. Locate the round hole that marks the center of the plastic strip (all other holes are slotted). Install a #8 x 5/8" Pan Head Screw in the round hole to secure the fabric to the header as well as to center the top.
Trektop NX Installation Instructions Secure Straps to Sport Bar Install Rear Window Loosen the speaker pod. Slip the straps between the speaker pod and the sport bar. Wrap the straps around the sport bar on each side of the vehicle. Thread the ends of the straps through the buckles and tighten. Tighten the speaker pod. Orient the Rear Window with the plastic J-slide toward the top. Align the J-slide with the J-slide sewn into the rear of the Top.
Trektop NX Installation Instructions Close Upper Zipper on Quarter Windows Install Quarter Windows Separate the protective flap covering the hook strip on the side of the Deck. Open the flap toward the inside of the vehicle. Close the zippers along the top of each Quarter Window. Push Plastic Reinforcement down to make it easier to close zipper. Start the zipper along the top of the Quarter Window with the zipper in the Top. Only close the zipper 1-2".
Trektop NX Installation Instructions Secure Top Fabric to Quarter Windows Install Tailgate Bar Open the tailgate. Orient the Tailgate Bar with the rubber bulb facing down, in order to form a seal with the top of the tailgate. Slide the groove in the Tailgate Bar onto the tube inside the bottom of the Rear Window. Roll the Tailgate Bar into the top of the Tailgate Mounts. Close the Rear Window zippers.
Trektop NX Installation Instructions Secure Header to Windshield Hook the latches on the Header into the holes in the windshield and close them. When operating the vehicle without the Quarter Windows, the Rear Window should be removed for proper ventilation. To Use Trektop NX as a Bikini Close Over Latch Your Bestop Trektop NX can be used as a Bikini by removing the Quarter Windows and Rear Window and storing them carefully. Fold the protective flaps over to engage the hook and loop tape.
Trektop NX Installation Instructions Care and Maintenance of your Bestop Product Your Bestop product is made of the finest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance. Fabric: The fabric should be washed often using soap, warm water and a soft bristle brush Rinse with clear water to remove all traces of soap. Bestop recommends using Bestop Cleaner (part no. 11201-00) and Bestop Protectant (part no.