50 Ft. Grease/Oil Hose Reel with Hose Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Roughneck™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This hose reel is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use The Roughneck 50 Foot Grease and Oil Hose Reel incorporates metal forms to ensure strength and function equally well in both mobile and permanent-mount situations that are suitable for a variety of heavy-duty applications in the mining, construction, service, and marine industries. #58247 is designed for water and oil. #58243 and #58269 can be used to transfer grease and oil. The hose reels have automatic rewind and easily install to a wall, floor, or ceiling.
⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust.
Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part. Do not use a product with a malfunctioning switch. Any power tool that cannot be controlled with the power switch is dangerous and must be repaired by an authorized service representative before using.
Main Parts of Product Page 7 of 17
Part No. Description Quantity Part No. Description Quantity 1 Spring 1 35 Nut 3 2 Drum for Spring 1 36 Set Screw 1 4 Drum 1 37 Washer Spacer 1 5 Drum 1 38 Washer 1 6 Base 1 39 Nut 1 7 Arm 1 46 Bolt 3 8 Guide Plate 1 47 Washer, Lock 3 9 Guide Sub-Plate 1 48 Nut, Lock 3 10 Axle 1 49 Bolt 4 11 Locking ring 1 50 Nut 4 12.
Prior to mounting the hose reel, ensure that the supply hose pressure does not exceed the maximum working pressure of the hose reel. Also check that the pressure source is turned off and the supply hose for the reel is not pressurized. Unpack the reel then check that all parts are present and inspect for damage. Check reel function for smooth rotation. Fasten the mounting base in the desired location. Reel dimensions and the pattern of the mounting holes in the base are shown below.
Note: Final spring tension adjustment is accomplished by adding wraps of hose around the drum (to increase tension) or taking off wraps of hose (to decrease tension). Refer to: Adjustment of Spring Tension. Figure 2. Before Each Use ⚠WARNING Before connecting a pressure source, ensure that supply pressure does not exceed the maximum working pressure rating of the reel and hose. Ensure that the reel is properly installed before connecting input and output hoses.
Do not kink the hose. Do not step on the hose or drive or drag objects over the hose. Do not place any objects on the hose or hose reel. Pull the hose from the reel by grasping the hose itself, not the valve. 1. 2. 3. 4. Check reel for correct operation by slowly pulling out the hose. A “clicking” noise will be heard every half revolution of the drum. To latch the reel, pull out the hose and allow it to retract after hearing the first, second, or third click.
After Each Use ⚠WARNING Bleed fluid/gas pressure from the reel before servicing. Use soap and water when checking for air leaks. Exposure of skin directly to pressurized air or fluids could result in severe bodily injury, including blood poisoning. Maintenance Maintain your reel. It is recommended that the general condition of any tool be examined before it is used.
Parts Diagram Page 13 of 17
Parts List Part No. Description Quantity Part No.
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Roughneck product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.