CENTURY Round Pools ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS CENTURY - ROUND - page 1
Installation Instructions 3. Do not attempt to lift the heavy boxes by yourself. To HOW TO USE THESE INSTRUCTIONS Be sure to read these instructions completely before reduce the possibility of personal injury, have someone help you move heavy boxes (pool wall, liner, etc.). beginning the installation of your pool. ATTENTION: warning Always use these assembly instructions to install 1. Your pool must be level within 2-3 cm all around. your swimming pool.
POOL SIZES Where to position my pool? Before you start building your pool, pay attention to the following points: 1. Garden fence. 2. Trees, roots, overhanging branches and falling leaves. Clearance radius 3,6 m round 3. Underground wiring or cables. 4. Position pool with regard to sun terrace or sunken 2,4 m sitting area. 5. Position pool with regard to the sunshine. 6. Supervision of small children. 7. Convenient location of filter and pump. 8. Convenient electrical outlet for the pump 9.
Step 1 Step 2 5x10 cm Nail Hole Cleara Centre nce rad 5x5 cm centre ius Bottom rail Water level 30 cm Patio block end cap Level Use a wooden stake as the centre and make a circle of the diameter of your pool. For this attach a wire or cord on the one hand to the wooden stake and on the other hand to a screw driver or marking pen. The size is half Depending on the size of your pool (please refer to the of the pool diameter starting from the wooden stake.
Step 5 Step 6 End cap Stud Holes Screws Screws Now place the studs such that the threaded hole is at the top front. The installation is connected together with Carefully adhere to the details indicated in Figure A for self tapping screws. A drop of oil on the self tappers the assembly of the end caps. makes your work easier.
ASSEMBLY OF THE GUARDS Step 10 liner side seam water face Step 8 Assemble the guards alongside the pool edge (guard panels). Hook de guard starting from the outside of the item number bottom seam Pool liner pool alongside the edge; afterwards click it on the inside towards the bottom. Guard panel End cap Remove the wooden stake and recheck the soil if there is gravel, glass or other sharp projections. Flatten foot prints and other unevenness.
Step 12 Step 14 Water level Garden hose 50cm Clamp Fill the pool up to approximately 50 cm below the cover Before filling up the pool, place binder clips between the panel. Make sure that during the filling the liner does not studs. These binder clips are available from the builder’s fall back into the pool. Water between the liner and the merchant.
Step 16 Stabilizer rail large Stabilizer rail small Plastic profile Pool liner Pool liner Pool wall Fold the overhanging part of the liner towards the outside of the steel wall and pull the whole liner tight (please refer to the drawing).
SUPPLEMENTARY INSTRUCTIONS FOR BUILDING A POOL IN THE GROUND To avoid that material rolls onto the site where the pool is to be constructed, the location where the pool is to INSTALLATION OF SKIMMER AND INLET be constructed must be in the most elevated part of the The skimmer and the inlet have to be installed before garden. The surrounding landscape should be lower the pool is filled with water and before the pool is filled than the pool.
Feed towards pump gate of filter Check valve (Recommended) Space between the top of the pool and stabilizer sand 22 cm Retour towards return gate filter Grade 2 cm per meter Stabilisierter Sand Füllen Sie erst das Schwimmbecken, bevor Sie den stabilisierten Sand auffüllen. Valve (Recommended) PVC tube and fixtures FIG. 2 SPECIFIC INSTALLATION IMPORTANT MESSAGE: bility to have easy access for maintenance or repairs.
Standard SKIMMER Fig. 1 Standard Skimmer MODELS 5-2091-015 INSTALLATION INSTRUCTIONS Cover Outside pool Inlet Sand filter Pool pump PREPARATION OF THE POOL The pool should be built up the correct way based on the pool assembly and installation instructions. Approximately 70 cm water should press against the metal wall, so that there isn’t any elasticity anymore against the liner, before the skimmer is installed. ATTENTION: After the skimmer hole is cut open the liner can no longer be moved.
Installation inlet fixture Fig. 2 1. Install the gasket of the inlet (17) into the wall opening. Insert the inlet fixture (18) through the liner and Inside pool Skimmer plate the wall starting from the inside of the pool. Make a small notch into the liner and press the inlet fixture through. 2. Now screw the inlet (16) onto the inlet fixture; turn it clockwise until the inlet end points towards the Skimmer valve Suction connection for cleaning pool bottom. 3.
Warning: Never try to install the cover in a suctioning Lid position if the pump is switched on. The cover might Vacuum adaptor suddenly be pulled down due to the strong suction of the pump. You may suffer personal injury to your hands or fingers. 5. When the cover is in place, you can switch on the Suction cover Fig. 7 pump and put into operation the suction of the pool floor. 6. When you are finished suctioning, you have to switch 3.
PREPARING FOR WINTER When the swimming season is over, you have to follow the instructions to get your pool ready for winter. ATTENTION! Do not remove all the water from your pool and also do not remove the liner. An empty pool can namely cause pool failure. Lower the water level - Lower the water level in your pool so that it is approximately 6” (15 cm) below the inlet fixture; maintain this water level by checking it regularly.