Ultra Professional Instructions for Use
IMPORTANT SAFETY INSTRUCTIONS When using your iron, basic safety precautions should always be followed, including the following: Read all instructions before using the iron. 1. Use iron only for its intended use. 2. To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3. The iron should always be turned to Minimum (Min) before plugging or unplugging from outlet. Never yank cord to disconnect from outlet, instead grasp plug and pull to disconnect. 4.
SPECIAL INSTRUCTIONS 1. This is a 1440 watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, a 12-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. 3. Your Rowenta appliance is intended for household use only.
E F G H I J K C/D L B A O ■ A B C D E F G H 4 Description: Spray nozzle Covered water filling inlet Variable steam control Self clean system Spray button Burst of steam button Auto-off indicator light Temperature control dial N I J K L M M Swiveling cord protector Supply cord Temperature light Long-Life System Precision Stainless Steel Soleplate N Transparent water tank O Water level indicator
BEFORE USE 왎 왎 왎 Please read the instructions for use and the Important Safeguards carefully. Remove the transparent soleplate protector. It is normal for a small amount of smoke to be produced the first time the iron is used. This will quickly disappear. 3-WAY AUTO-OFF 30 sec. 8 min. 30 sec. If the iron is not moved while it is plugged in, an internal safety switch will turn it off. It will turn off in 8 minutes if left vertically or in 30 seconds if left on its soleplate or tipped over.
SELECTING THE TEMPERATURE Set the temperature control dial according to the type of fabric you are ironing. Check the fabric's label for appropriate setting. Laundry label Fabric Temperature setting synthetics e.g. viscose, polyester ● silk, wool ●● cotton, linen ●●● To avoid an automatic switch off while the iron is heating up, always keep the iron on its heel. Start at low temperature ● and graduate to high temperature ● ● ●.
SPRAY SETTING 왎 왎 왎 왎 Ensure there is water in the tank. Moistening the fabric with the spray will make wrinkle removal easier. Press the spray button down slowly for a jet or quickly and strongly for a mist. Do not spray silk, etc. BURST OF STEAM 왎 왎 왎 왎 To remove stubborn wrinkles or press in a sharp crease, use the burst of steam button. Press the button firmly, a strong burst of steam penetrates deep into the fabric.
AFTER IRONING 왎 Unplug the iron. Slide the variable steam control completely to the left (the minimum position) and empty any water left in the tank. Leave the iron to cool down. Integrated cord wrap 왎 왎 For easy storage, the cord can be wound loosely around the heel once the iron has cooled down completely. To protect the soleplate always store the iron on its heel. Important: Always empty the water tank when you have finished ironing.
LONG-LIFE SYSTEM Minerals in water can build up in the steam chamber as the water is tumed to steam. This build up reduces steam output over time. The Long-Life System contains a special resin that neutralizes the harmful minerals, extending the life of the iron. The resin is irtegrated into the tank and never needs to be replaced. SELF CLEANING Your iron is equipped with two self clean functions.
CLEANING AND MAINTENANCE 왎 When cold and unplugged, the iron can be cleaned with a damp cloth and wiped dry. Never use household cleaners or solvents. Cleaning the soleplate Rowenta stainless steel soleplates have excellent non-stick properties and can be simply wiped clean when cold. 왎 In normal use a draggy coating may build up on the soleplate (starch, detergent buildup, burnt synthetic fibers).
IRON TROUBLESHOOTING Problem Possible cause Solution Iron is leaking. DISTILLED WATER DO NOT use 100% pure distilled water, use tap water. In very hard water areas mix half tap water with half distilled to reduce hardness; or use inexpensive bottled spring water. SOFTENED WATER Most softened water is alright, but if you experience leaks or spitting, change to untreated tap water or inexpensive bottled spring water. DO NOT use 100% distilled water. Iron won’t heat.
