Professional Luxe Instructions for Use
IMPORTANT SAFETY INSTRUCTIONS When using your iron, basic safety precautions should always be followed, including the following: Read all instructions before using the iron. 1. Use iron only for its intended use. 2. To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3. The iron should always be turned to Minimum (Min) before plugging or unplugging from outlet. Never yank cord to disconnect from outlet, instead grasp plug and pull to disconnect. 4.
SPECIAL INSTRUCTIONS 1. This is a 1400 watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, a 12-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. 3. Your Rowenta appliance is intended for household use only.
E F GHI J K C/D L B A N ■ A B C D E F G 4 Description: Spray nozzle Covered water filling inlet Variable steam control Self clean system Spray button Burst of steam button Auto-off indicator light (depending on model) M H I J K L M Pilot light Temperature control dial Flexible cord protector Power cord Transparent water tank Stainless steel soleplate (depending on model) N Water level indicator
BEFORE USE 왎 왎 왎 Please read the instructions for use and the Important Safeguards carefully. Remove the transparent soleplate protector. It is normal for a small amount of smoke to be produced the first time the iron is used. This will quickly disappear. 3-WAY AUTO-OFF (depending on model) 30 sec. 8 min. 30 sec. If the iron is not moved while it is plugged in, an internal safety switch will turn it off.
SELECTING THE TEMPERATURE Set the temperature control dial according to the type of fabric you are ironing. Check the fabric's label for appropriate setting. Laundry label Fabric Temperature setting synthetics e.g. viscose, polyester ● silk, wool ●● cotton, linen ●●● To avoid an automatic switch off while the iron is heating up, always keep the iron on its heel. Start at low temperature and graduate to high temperature.
SPRAY SETTING 왎 왎 왎 왎 Ensure there is water in the tank. Moistening the fabric with the spray will make wrinkle removal easier. Press the spray button down slowly for a jet or quickly and strongly for a mist. Do not spray silk, etc. BURST OF STEAM 왎 왎 왎 왎 To remove stubborn wrinkles or press in a sharp crease, use the burst of steam button. Press the button firmly, a strong burst of steam penetrates deep into the fabric.
DRY IRONING Slide the variable steam control fully to the left. We recommend dry ironing with an empty tank to be sure there are no drips, but it can also be performed with water in the tank. 왎 min Self max Clean AFTER IRONING 왎 Unplug the iron. Set the variable steam control to max. and empty any water left in tank. Then set the variable steam control to min. and leave the iron to cool down.
Iron and other impurities If your water supply contains large amounts of iron or organic matter, these minerals can collect inside the iron and eventually appear as brown stains. If you experience these problems Rowenta recommends using inexpensive bottled spring water. Never use 100% pure distilled water. Always remember: Battery water and water containing additives (such as starch, perfume or fabric conditioner) may not be used.
WARNING: Iron and soleplate may still be hot, exercise care while wiping. 왎 왎 Place iron on heel and leave to cool. IMPORTANT: before using the iron after self cleaning, test steam and burst of steam on an old towel or cloth to ensure all loose material has been removed from the iron. CLEANING AND MAINTENANCE 왎 When cold and unplugged, the iron can be cleaned with a damp cloth and wiped dry. Never use household cleaners or solvents.
IRON TROUBLESHOOTING Problem Possible cause Solution Iron is leaking. DISTILLED WATER DO NOT use 100% pure distilled water, use tap water. In very hard water areas mix half tap water with half distilled to reduce hardness; or use inexpensive bottled spring water. SOFTENED WATER Most softened water is alright, but if you experience leaks or spitting, change to untreated tap water or inexpensive bottled spring water. DO NOT use 100% distilled water. Iron won’t heat.
