USER’S GUIDE LCD MONITOR S-5 (S-50TP)
IMPORTANT SAFETY INFORMATION • Read all of these instructions carefully, and save them for reference. Follow all warnings and instructions marked on the product. • Unplug the monitor from the system unit before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. • Use only attachments recommended by the manufacturer; unapproved attachments may be hazardous.
• To protect the monitor during a lightening storm or when it is left unattended and unused for long periods of time, unplug it from the system unit. This will prevent damage to the monitor from lightening and power surges. • Do not overload power outlet and extension cords. Overload can result in fire or electric shock. • Never push any object into the slot in the monitor cabinet. It could touch dangerous voltage points or short out parts resulting in a fire or electric shock.
FCC Class B Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
TABLE OF CONTENTS 1. INTRODUCTION .............................................................................1 1.1 General information..................................................................1 1.2 Features..................................................................................1 1.3 Check List ...............................................................................2 2. SETUP............................................................................................3 2.
1 INTRODUCTION 1.1 General Information The S-50TP is a 15.0-inch intelligent LCD monitor with ultra high resolution of up to 1024 x 768. The microprocessor-based design was implemented with the user in mind. We invite you, the proud new owner of this fine monitor, to read this user’s manual before operating, in order to get the most out of this product. 1.2 Features ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³ 15.0" Large Size XGA TFT LCD Panel 0.297mm(H) x 0.
Figure 1 1.
2 SETUP 2.1 LCD Monitor setup Figure 2 2.1.1 Power Cable Connection Plug the power cable into the wall outlet, the other end of the power cable into the AC socket. 2.1.2 Signal Cable Connection Connect the VGA cable to the back of S-50TP monitor. 2.1.3 Power On Turn on the power of both your S-50TP monitor and your computer.
3 USER INTERFACE CONTROL There are some switches, power LED and OSD menu on the S-50TP. These are to provide the users an easy way to adjust video and audio. A description of these functions is as follows: 3.1 OSD Controls To make any adjustment: 1. 2. 3. 4. Press (MENU / EXIT) key to show the OSD menu or disable OSD menu. Select the item in the menu that you wish to adjust by turning flywheel. Press (ENTER) key to make this item adjustable. Adjust the item that you selected by turning the flywheel.
7. FINE TUNE ( ): Shifts the pixel clock phase when video jitter happens or focus is not perfect. Video jitter may cause by the difference of VGA card or the big change in weather. 8. AUTO SIZE ( ): Adjust the screen position and clock phase automatically. 9. COLOR ( , ): Step 1: Select R, G, or B to begin adjusting by turning flywheel. Step 2: Use the (ENTER) key to make this item adjustable. Step 3: Adjust the item by turning flywheel. Red Control ( R ) Increases/Decreases the red video gain level.
3.1.2 Recommend Solution and Mode S-50TP We recommend that user choice one of the following modes. Show as follows: Resolution Hor-frequency Ver-frequency 640*350 31.467(+ ) 70.082(-) 720*400 31.467(-) 640*480 31.409(-) 70.082(+) 59.487(-) 640*480 37.861(-) 72.809(-) 640*480 37.500(-) 75.000(-) 800*600 35.156(+) 56.250(+) 800*600 37.879(+) 60.317(+) 800*600 48.077(+) 72.188(+) 800*600 46.875(+) 75.000(+) 1024*768 48.363(-) 60.004(-) 1024*768 56.476(-) 70.
3.2 Front Panel Controls Figure 3 3.2.1 Menu /Enter Button Press this button to show OSD menu or select the item you want to adjust. 3.2.2 Brightness Hot Key Function Turn the flywheel counterclockwise to adjust the brightness directly. 3.2.3 Contrast Hot Key Function Turn the flywheel clockwise to adjust the contrast directly. 3.2.4 Power Button ( Press ( 3.3 ) ) to turn the power on or off.
4. PLUG AND PLAY 4.1 DDC Function The Display Data Channel“DDC”will allow the display to inform the host system about its identity and depending on the level of DDC used, communicate additional levels of display capability. DDC 1: One uni-directional data channel. DDC 2: One bi-directional data channel. S-50TP can support display type DDC1/2B. 5.
5.
6. TROUBLESHOOTING Problem : No picture appears on the screen. If power LED is off, check if power cable is securely connected. If power LED is amber in color, check if video cable is securely connected. Also check if your computer is switched on. If power LED is green in color, check if H SYNC frequency is out of range. Adjust the brightness and contrast controls. Problem : Picture is unstable (noise, jitter etc) Check the timing of your computer and see if they are compatible with S-50TP. 7.
Specifications LCD Panel: 1. Display Area : 304.1 (H) x 228.1(V) mm 2. Number of pixels : 1024 x 768 3. Pixel pitch : 0.297(H) x 0.297(V) mm 4. Contrast ratio : 300:1(typ ., perpendicular) 5. Viewing angle (more than the contrast ratio of 10:1) Horizontal : 50° (typ. ,left side, right side) Vertical : 40°,60° (typ. ,up side, down side) 6. Response time : 11ms (typ.), (white to black) 19ms(typ.), (black to white) 7. Luminance : 250cd/m2 (typ.) Video and Synchronization Signals: 1. Signal cable 2. Video 3.
Regulatory: 1. Optional FCC-B/UL/CSA 2. Optional TÜV-GS 3. Optional CE 4. Optional MPRII 5.
