Use and Care Manual

OSCILLATION
The fan is preset to oscillation setting
· Oscillation Setting: Loosen the screw on the oscillation rod and move
to the end of the oscillation cam. Tighten the screw to lock the position.
(See Figure 1)
· Non Oscillation Setting: Loosen the screw on the oscillation rod and move to the center
of the oscillation cam. Tighten the screw again to lock the position.
(See Figure 2)
PFNC-30
Owner's Manual
Royal Sovereign International Inc.
Please read and retain these instructions
Because our products are subject to continuous improvement, Royal Sovereign reserves the right to modify product design
and specificationswithout notice and without incurring any obligation. E&OE
30" INDUSTRIAL
OSCILLATING PEDESTAL FAN
SAFETY INSTRUCTIONS
CAUTION: Read and follow all instructions before operating fan. Do not use fan if any part is
damaged or missing.
WARNING:
- To reduce the risk of fire or electrical shock, do not expose to water or rain.
-
To reduce the risk of fire or electrical shock, do not use this fan with any solid state speed control device.
- Automatically operated device - To reduce the risk of injury, disconnect from power supply before servicing.
- If the power supply cord is damaged, contact your local service center or a qualified
electrician to install an appropriate replacement cord to prevent any injury or damage.
- The appliance does not apply to be used in locations where special conditions prevail,
such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas ).
- This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance
ADDITIONAL SAFETY PRECAUTIONS:
1. Never insert fingers or any other objects through the grill guard when fan is in operation.
2. Disconnect the fan from its power source when moving from one location to another.
3. Disconnect the fan from its power source when removing guards for cleaning.
4. Be sure fan is on a stable, flat surface when in operation.
5. Do not use fan in windows. Rain and moisture may create an electrical hazard.
6. Close supervision is necessary when this fan is used near children, the elderly and pets.
7. Do not place the fan near an open flame, cooking or heating appliance, or hot surface.
8. This fan should not be operated outside.
CAUTION: Do not alter the fan's assembly.
WARNING:
Be sure that both front and rear guard screws are completely tightened in
locking position before operation.
STEP 1 - COLUMN ASSEMBLY INSTRUCTIONS:
1. Attach coupling to the base with the screws as shown in diagram.
2. Loosen set screw on the outer tube coupling and extend inner tube to desired height
tighten. Ensure that the set screw is securely tightened.
IMPORTANT NOTE:
The set screw must be fully tightened before assembling the motor
to the innertube.
STEP 2 - COLUMN / MOTOR ASSEMBLY INSTRUCTION:
1. Align motor flange and column.
2. Insert the pivot screw through the motor flange, column and washer. Attach with
nut. Tighten firmly.
3. Insert smaller position knob through bottom radius. Attach with washer and nut,
tighten firmly.
STEP 3 - GRILL / MOTOR ASSEMBLY INSTRUCTIONS:
1. Unscrew the set screws from the motor.
2. Set the rear guard in its proper position.
3. Attach the rear guard by inserting and tightening the set screw to the motor
4.
Insert the blade on the shaft until it reaches a stopping point and the set screw is in
line with the flat groove on the shaft .
NOTE: Be sure the set screw of your blade is facing the motor of your fan. You may need to
loosen the set screw at the rear of the bladeto slide easily onto the shaft.
5. Securely tighten the blade set screw.
IMPORTANT NOTE: DO NOT ALTER THE ANGLES OF BLADE.
6. Turn the clips on the front guard outward.
7. Mount the front guard with the groove at the guard's top sliding into its proper position (
the Royal Sovereign nameplate should be positioned forward).
8. Fasten and lightly tighten grille screws and washers on thefront guard to the back guard.
9. Press both front guard and back guard together.
10.
Push front guard's clips downward into the locking position.
11. Completely tighten grill screws washers on front guard and into back guard.
VERTICAL TILT:
To adjust tilt, loosen the position screw first and then loosen the pivot bolt. Tilt motor
to the desired angle then firmly tighten the pivot bolt first and then tighten the position screw.
SPEED CONTROL:
Select air speed by setting switch to either HIGH, LOW or OFF.
CLEANING
WARNING: Unplug from electrical supply source before cleaning.
1. Use soft damp cloth, then wipe with dry cloth.
2. Do not use harmful cleaners to paints or plastics.
3. Do not bend the blades.
IMPORTANT:
Surges in electrical power or excessive heat may cause
the fan to turn off. Wait approximately 15 minutes for the fan to
resume operation.
SPECIFICATIONS
Model Name PFNC-30
Fan Size 30"
Settings High /Low/OFF
Air Delivery (High/Low) 8400 cfm / 7150 cfm
Speed (High/Low) 1100 /950 rpm
Decibel (High/Low) 67 /64 dB
Motor 1 /3 HP
Adjustable Height 60-78"
Tilt Up to 30°
Blade Aluminum
Amperage (High/Low) 2.1 /1.64 a
Voltage 120/60 Hz
Wattage (High/Low) 250 /185 W
Unit (w x h) 31.5" x 60" (adjustable)
Base 27.7" (Metal Base)
Unit Weight 43.5 lbs.
WARRANTY
Royal Sovereign warrants each fan to be free from defects in material and workmanship. Our
obligation under this warranty is limited to the repair or replacement, free of charge, when
delivered to an authorized Royal Sovereign service center, of any defective part(s) thereof,
other than parts damaged in transit. This warranty is in effect to the original purchaser, for a
period of one year from the date of purchase and is not transferable. This warranty shall apply
only if the fan is used in accordance with the factory provided instructions which accompany it.
EXCLUSIONS
This warranty excludes and does not cover defects, malfunctions or failures of your Royal
Sovereign Fan, caused by repairs by unauthorized persons or service centers, mishandling,
improper installation, modification or unreasonable use including incorrect voltage, acts of God,
or failure to provide reasonable and necessary maintenance. This warranty is in lieu of any and
all expressed warranties. In no event shall Royal Sovereign be liable for consequential or
incidental damages. This limitation would not apply if you live in a location that does not permit
the exclusion of limitation of incidental or consequential damages.
ROYAL SOVEREIGN INTERNATIONAL, INC.
2 Volvo Drive Rockleigh, NJ 07647 USA
TEL : [phone]
FAX : [phone]
www.royalsovereign.com
RS INTERNATIONAL CANADA INC.
5610 Timberlea Blvd, Mississauga Ontario L4W 4M6 CANADA
TEL: [phone] TF: +1) 8
66 961-6673
FAX: [phone]
www.royalsovereign.ca