Owner's Manual

13
Toggle Switch: The fireplace has a main toggle
switch located next to the manual controls.
The toggle switch is in front of the glass on
the top right side of the viewing area.
When the “-” side of the toggle switch
is depressed, the “O” pops up.
This is the power-on state of the fireplace.
Power Indicator lights: The fireplace is equipped
with Power indicator lights which are located
on the upper right corner of the fireplace
viewing area.
First light: When the fireplace is in the power-on
state, an amber light turns on. The light shows
the fireplace is energized and on stand-by for
any commands. The amber light turns OFF
when the fireplace is turned on and operating.
Second light: When the fireplace is powered on
and the heater is set to low, the second light
turns on. Light will fade away after 6 seconds.
Third light: When the fireplace is powered on and
the heater is set to high, the third light turns
on. Light will fade away after 6 seconds.
Manual Controls
The fireplace has manual controls located next to the
toggle switch, in front of the glass on the top right
side of the viewing area.
Power On/Off button: Press once, indicator light turns
off and fireplace power turns on. All functions
enabled. Press again, flame turns off and fireplace
goes to standby. NOTE: Long pressing this button
for 3 seconds places fireplace in RF pairing mode.
Heat Button: Pressing heat button cycles the heater
and blower on/off. Settings: Heater and blower
OFF, Low Heat, and High Heat. Indicator light will
match according to status. NOTE: On US LPM, low
and high heat have the same heat output when
wired for 120 V. Long Press the heater button for 5
seconds to lock/unlock the heater.
Preset Color Button: Press preset color button to
cycle through the 8 preset color options. This
changes color of all three zones: the flame, ember
bed and down light. Colors in order of appearance:
MF orange-red-orange-golden
orange-green-aqua-blue-magenta
Resetting button: Clears any paired remotes/devices
from the fireplace. Once cleared you can pair a
new remote or wall touch control. This will also
un-pair any APP that was paired to the fireplace.
After long pressing the reset button for 3 seconds,
a beeping tone will be heard indicating that the
pairing codes have been cleared.
Buzzer Tone Change: Long press the on/off and
preset color button at the same time to enter the
beeping tone cycle mode. Continue to long press
both buttons to cycle through the 4 tone options.
The tone will change every 2 seconds while releas-
ing the buttons will act as the selection of the tone.
The tones in order of appearance are; tone-1,
tone-2, tone-3, and silent mode.
Power
Turns unit
on/off
Heat
Cycles
heat low/
high/off
Color
Changes all
fireplace
colors
together
Reset
Resets
unit
SETTING CONTROLS
NOTE: When silent mode is selected, a tone will still
be present for performing system functions such
as remote pairing or Wi-Fi pairing.
Placing in Wi-Fi Paring Mode:
-EZ Mode: While the fireplace is ON, long press
the Preset Color button for 3 seconds. An audible
beeping tone will sound and the flame light, ember
bed light, and down light will turn to white and
begin flashing rapidly. Fireplace is now in EZ
pairing mode, which lasts for 2 minutes.
-AP Mode: While the fireplace is ON, long press
the Preset Color button for 6 seconds. Two audible
beeping tones will sound and then only the FLAME
LIGHTS and nothing else will turn to white and
begin flashing slowly. Fireplace is now in AP pairing
mode, which lasts for 2 minutes.
NOTE: Fireplace is also equipped with Bluetooth
pairing. There is no mode setting for the Bluetooth
as the APP will automatically detect the Bluetooth
signal for pairing when attempting to pair fireplace
to Bluetooth.