Instruction manual

This unit provides a useful function parameter "FUNC", this is used to select
the Function Complexity Level before setup. If the Basic Mode (FUNC =
BASC) is selected for a simple application, then the following functions are
ignored and deleted from the full function menu:
RAMP, SP2, PB2, TI2, TD2, PL1, PL2, COMM, PROT, ADDR, BAUD, DATA,
PARI, STOP, AOFN, AOLO, AOHI, IN2, IN2U, DP2, IN2L, IN2H, EIFN, PVMD,
FILT, SLEP, SPMD and SP2F.
This
unit provides a useful function parameter "FUNC", this is used to select
the
Function Complexity Level before setup. If the Basic Mode (FUNC =
BASC)
is selected for a simple application, then the following functions are
ignored
and deleted from the full function menu:
RAMP,
SP2, PB2, TI2, TD2, PL1, PL2, COMM, PROT, ADDR, BAUD, DATA,
PARI,
STOP, AOFN, AOLO, AOHI, IN2, IN2U, DP2, IN2L, IN2H, EIFN, PVMD,
FILT,
SLEP, SPMD and SP2F.
(1) Second set point
(2) Second PID
(3) Event input
(4) Soft start (RAMP)
(5) Remote set point
(6) Complex process value
(7) Output power limit
(8) Digital communication
(9) Analog retransmission
(10) Power shut off (Sleep Mode)
(11) Digital filter
(12) Pump control
(13) Remote lockout
(1) Second set point
(2)
Second PID
(3)
Event input
(4)
Soft start (RAMP)
(5)
Remote set point
(6)
Complex process value
(7)
Output power limit
(8)
Digital communication
(9)
Analog retransmission
(10)
Power shut off (Sleep Mode)
(11)
Digital filter
(12)
Pump control
(13)
Remote lockout
(1) Input 1: Thermocouple, RTD, Volt, mA
(2) Input 2: CT for heater break detection
(3) Output 1: Heating or Cooling ( Relay, SSR, SSRD, Volt, mA )
(4) Output 2 : Cooling ( Relay, SSR, SSRD, Volt, mA ), DC Power supply.
(5) Alarm 1: Relay for Deviation, Deviation Band, Process, Heater Break, Loop
Break, Sensor Break, Latch, Hold or Normal Alarm.
(6) Alarm 2: Relay for Deviation, Deviation Band, Process, Heater Break, Loop
Break, Sensor Break, Latch, Hold or Normal Alarm.
(7) Dwell Timer
(8) Heater Break Alarm
(9) Loop Break Alarm
(10) Sensor Break Alarm
(11) Failure Transfer
(12) Bumpless Transfer
(13) PV1 Shift
(14) Programmable SP1 Range
(15) Heat-Cool control
(16) Hardware Lockout
(17) Self-Tune
(18) Auto-Tune
(19) ON-OFF, P, PD, PI, PID Control
(20) User Defined Menu (SEL)
(21) Manual Control
(22) Display Mode
(23) Reload Default Values
(24) Isolated DC Power Supply
(25) PV or SV Selection
(1) Input 1: Thermocouple, RTD, Volt, mA
(2)
Input 2: CT for heater break detection
(3)
Output 1: Heating or Cooling ( Relay, SSR, SSRD, Volt, mA )
(4)
Output 2 : Cooling ( Relay, SSR, SSRD, Volt, mA ), DC Power supply.
(5)
Alarm 1: Relay for Deviation, Deviation Band, Process, Heater Break, Loop
Break,
Sensor Break, Latch, Hold or Normal Alarm.
(6)
Alarm 2: Relay for Deviation, Deviation Band, Process, Heater Break, Loop
Break,
Sensor Break, Latch, Hold or Normal Alarm.
(7)
Dwell Timer
(8)
Heater Break Alarm
(9)
Loop Break Alarm
(10)
Sensor Break Alarm
(11)
Failure Transfer
(12)
Bumpless Transfer
(13)
PV1 Shift
(14)
Programmable SP1 Range
(15)
Heat-Cool control
(16)
Hardware Lockout
(17)
Self-Tune
(18)
Auto-Tune
(19)
ON-OFF, P, PD, PI, PID Control
(20)
User Defined Menu (SEL)
(21)
Manual Control
(22)
Display Mode
(23)
Reload Default Values
(24)
Isolated DC Power Supply
(25)
PV or SV Selection
Basic Mode capabilities:Basic Mode capabilities:
If you don't need:If you don't need:
then you can use Basic Mode.then you can use Basic Mode.
Chapter 3 Programming the Basic FunctionChapter 3 Programming the Basic Function
3 1 Input 13 1 Input 1
Press to enter Setup Mode. Press to select parameter. The upper
display indicates the parameter symbol, and the lower display indicates the
selection or the value of parameter.
Press to enter Setup Mode. Press to select parameter. The upper
display
indicates the parameter symbol, and the lower display indicates the
selection
or the value of parameter.
IN1 : Selects the sensor type and signal type for Input 1.IN1 : Selects the sensor type and signal type for Input 1.
Range:
Default :
J-TC, K-TC, T-TC, E-TC, B-TC, R-TC, S-TC,
N-TC, L-TC
PT.DN, PT.JS
4-20, 0-20, 0-1V, 0-5V, 1-5V, 0-10
J-TC if F is selected, K-TC if C is selected.
Thermocouple:
RTD:
Linear:
Range:
Default
:
J-TC,
K-TC, T- T C , E-TC, B-TC, R-TC, S-TC,
N-TC,
L-TC
PT.DN,
PT.JS
4-20,
0-20, 0-1V, 0-5V, 1-5V, 0-10
J-TC
if F is selected, K-TC if C is selected.
Thermocouple:
RTD:
Linear:
IN1U:
Range:
Default:
Selects the process unit for Input 1.
C, F, PU ( process unit ) If the unit is neither C nor F, then
selects PU.
Cor F.
IN1U:
Range:
Default:
Selects the process unit for Input 1.
C, F,
PU ( process unit ) If the unit is neither C nor F, then
selects
PU.
C
or F.
DP1 :
Range:
Default:
Selects the location of the decimal point for most ( not all ) process
related parameters.
( For T/C and RTD ) NO.DP, 1-DP
( For Linear ) NO.DP, 1-DP, 2-DP, 3-DP
1-DP
DP1 :
Range:
Default:
Selects the location of the decimal point for most ( not all ) process
related
parameters.
(
For T/C and RTD ) NO.DP, 1-DP
(
For Linear ) NO.DP, 1-DP, 2-DP, 3-DP
1-DP
IN1
IN1U
DP1
40