Instruction manual

3 19 Self tuning3 19 Self tuning
Self-tune MenuSelf-tune Menu
Selects
Disable Self-tuning
Disable Self-tuning
Enable Self-tuningEnable Self-tuning
or
58
The Self-tuning which is designed by using an provides an
alternative option for tuning the controller. It is activated as soon as SELF is
selected with YES. When Self-tuning is working, the controller will change its
working PID values and compares the process behavior with previous cycle. If
the new PID values achieve a better control, then changing the next PID values
in the same direction, otherwise, changing the next PID values in reverse
direction. When an optimal condition is obtained, the optimal PID values will be
stored in PB1, TI1, TD1 or PB2, TI2, TD2 which is determined by Event Input
conditions. See . When Self-tuning is completed, the value of SELF
innovative algorithm
Section 4-1
The Self-tuning which is designed by using an provides an
alternative
option for tuning the controller. It is activated as soon as SELF is
selected
with YES. When Self-tuning is working, the controller will change its
working
PID values and compares the process behavior with previous cycle. If
the
new PID values achieve a better control, then changing the next PID values
in
the same direction, otherwise, changing the next PID values in reverse
direction.
When
an optimal
condition is obtained, the optimal PID values will be
stored
in PB1, TI1, TD1 or PB2, TI2, TD2 which is determined by Event Input
conditions.
See . When Self-tuning is completed, the value of SELF
innovative
algorithm
Section
4-1
When the Self-tuning is enabled, the control variables are tuned slowly so that
the disturbance to the process is less than auto-tuning. Usually, the Self-tuning
When
the Self-tuning is enabled, the control variables are tuned slowly so that
the
disturbance to the process is less than auto-tuning. Usually, the Self-tuning
Exceptions: The Self-tuning will be disabled as soon as one of the following
conditions occurs:
1. SELF is selected with NONE.
2. The controller is used for on-off control, that is PB=0.
3. The controller is used for manual reset, that is TI=0.
4. The controller is under loop break condition.
5. The controller is under failure mode (e.g. sensor break).
6. The controller is under manual control mode.
7. The controller is under sleep mode.
Exceptions: The Self-tuning will be disabled as soon as one of the following
conditions
occurs:
1.
SELF is selected with NONE.
2.
The controller is used for on-off control, that is PB=0.
3.
The controller is used for manual reset, that is TI=0.
4.
The controller is under loop break condition.
5.
The controller is under failure mode (e.g. sensor break).
6.
The controller is under manual control mode.
7.
The controller is under sleep mode.
If the self-tuning is enabled, the auto-tuning can still be used any time. The self-If the self-tuning is enabled, the auto-tuning can still be used any time. The self-
Unlike auto-tuning, Self-tuning will produce less disturbance to the process.
Unlike auto-tuning, Self-tuning doesn't change control mode during tuning
period. It always performs PID control.
Changing set point during Self-tuning is allowable. Hence, Self-tuning can
be used for ramping set point control as well as remote set point control
Unlike auto-tuning, Self-tuning will produce less disturbance to the process.
Unlike
auto-tuning, Self-tuning doesn't change control mode during tuning
period.
It always performs PID control.
Changing
set point during Self-tuning is allowable. Hence, Self-tuning can
be
used for ramping set point control as well as remote set point control
Benefits of Self-tuning:Benefits of Self-tuning:
1.
2.
3.
Default
SELF=NONE
Default
SELF=NONE
Benefits of Self-tune:
1. Less disturbance to the process.
2. Perform PID control during tuning
period.
3. Available for ramping set point
control and remote set point
control.
Benefits of Self-tune:
1.
Less disturbance to the process.
2.
Perform PID control during tuning
period.
3.
Available for ramping set point
control
and remote set point
control.
Operation:
Section 1-5The parameter SELF is contained in setup menu. Refer to to
obtain SELF for initiating a self-tuning.
Operation:
Section 1-5The parameter SELF is contained in setup menu. Refer to to
obtain SELF for initiating a self-tuning.