ADAM™ CS Advanced Digital Audio Matrix System Installation Guide ADAM CS TM Advanced Digital Audio Matrix POWER GOOD 9330-7517-000 Rev H POWER GOOD July 31, 2006
PROPRIETARY NOTICE SHIPPING TO THE MANUFACTURER The product information and design disclosed herein were originated by and are the property of Telex Communications, Inc. Telex reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed therein, except to the extent rights are expressly granted to others. All shipments of product should be made via UPS Ground, prepaid (you may request from Factory Service a different shipment method).
Table of Contents Chapter 1 Introduction and Installation .............................................................................................................................3 ADAM CS Front Panel .....................................................................................................................................3 ADAM CS Back Panel .....................................................................................................................................
List of Tables ADAM CS, J903 Connector Pinout ......................................................................................................................15 ADAM CS Master Controller Card DIP Switch Settings (S1) .............................................................................19 Relationship between Audio Input/Output Cards, Intercom Ports, and Logical Keypanel Numbers ..................20 Address Switch Settings for KP-95/96/97/98 Keypanels and the TIF-2000 Telephone Interface ......
List of Figures ADAM CS Front View ......................................................................................................................................... 11 ADAM CS Back View (Shown with RJ-11 Connector Panel) ............................................................................ 12 ADAM CS J900 to Computer Interconnect Cables (ADAM CS with male J900 Connector) ............................. 13 ADAM CS J900 to Computer Interconnect Cables (ADAM CS with female J900 Connector) ........
CHAPTER 1 Introduction and Installation NOTICE: These servicing instructions are for use by qualified personnel only. To avoid electric shock do not perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so. ADAM CS Front Panel There are 10 card slots in the front panel. Starting from the left side, slots 1 through 8 are for Audio Input/Output (AIO) Cards. Slots 9 and 10 are for main and backup Master Controller Cards.
Introduction and Installation ADAM CS Frame Installation The ADAM CS Frame is equipped with rubber feet for placement on a desktop. For installation in an equipment rack, it may be necessary to remove the feet. Verify that the ventilation holes on the front and back are not obstructed. Allow space in back for attachment of connectors (at least 24 inches).
Power Supply Removal /Installation Master Controller Notes • As shipped from the factory, all master controller card DIP switches are set for default operation. These settings will be satisfactory for most applications. Optional settings are summarized in Table 2, “ADAM CS Master Controller Card DIP Switch Settings (S1),” on page 19. If you change any settings, make sure both the main and backup master controller cards are set the same.
Introduction and Installation 6
CHAPTER 2 Operation System Power Up NOTE: For proper power supply loading, at least two circuit cards should be installed in the frame before turning on the power supplies. 1. Place the AC switches on the back of the ADAM CS Frame in the ON position. The AC fans should turn on. 2. Place the ALARM OVERRIDE switch on the front panel in the center position. 3. Place the on/off switch on the front of each power supply in the ON position. The POWER indicators and all the voltage indicators should be lit.
Operation Software Installation Now that the ADAM CS frame is operating and the configuration computer is connected, you are ready to install the AZedit software and verify the computer can communicate with the intercom system. Follow the directions to install the software that accompanied the AZedit CD. AZedit gives you online help after starting the software. When the keypanel setup screen appears (the default setup screen), press F1 to start help, then select “Help Contents”.
Trunking System • Briefly note the device type (keypanel, TIF, program source, CDP-950, etc.). Other useful information might include the device location and usage, as well as any labeling on the intercom cable. • Write down a name of up to eight characters in the “Alpha” column of the worksheet. You will enter this name inot the intercom system later using AZedit. Then, whenever you assign the port to an intercom key, the name will appear in the keypanel display for that key.
Operation intercom system. There is no apparent difference to keypanel operators, but what actually occurs in the system electronics is slightly different. When a keypanel operator activates a key to talk to a destination located in another intercom system, the intercom system’s master controller does not act itself to close any crosspoints, but rather, it sends this information to the trunking system via the data connection. The trunking system master controller then checks for an available trunk line.
UIO-256 Input/Output Frame Additonal UIO-256s 1. Up to 15 additional UIO-256 frames may be connected in a parallel bus configuration using the 15-pin ribbon cables provided. Connect the J3 output of the ADAM MC to the J2 connection on the UIO-256. Connect J2 output of the first UIO256 to the input for the second UIO-256 to the J2 input of the third UIO-256. Continue connecting more UIO-256s in this manner. 2.
AC1 Connector for PS1 Power Supply AC2 Connector for PS2 Power Supply Operation J900 J902 J901 J903 J500 J501 J502 J503 J504 J505 J506 J507 J100 J101 J102 J103 J104 J105 J106 J107 J600 J601 J602 J603 J604 J605 J606 J607 J200 J201 J202 J203 J204 J205 J206 J207 J700 J701 J702 J703 J704 J705 J706 J707 J300 J301 J302 J303 J304 J305 J306 J307 J800 J801 J802 J803 J804 J805 J806 J807 J400 J401 J402 J403 J404 J405 J406 J407 J900: RS232 TO CONFIGURATION PC J901: RS422/232 TO TRUNK MASTER J902: RS422/2
UIO-256 Input/Output Frame ADAM CS J900 to Computer Interconnect Cables (ADAM CS with male J900 Connector) FIGURE 3.
Operation CONTACTS RJ12 MODULAR PLUG AMP 5-555042-3 or equivalent (View from cable entrance) 123456 Use AMP Chordal Crimp Tool 231648-1 or equivalent LATCH 3 TWISTED PAIR TELEPHONE CABLE PAIR 1: AUDIO TO MATRIX PAIR 2: AUDIO FROM MATRIX PAIR 3: DATA 1 2 3 4 5 6 FIGURE 5. FIGURE 6.
UIO-256 Input/Output Frame RJ-11 to 9-pin Intercom Cable. Used for TIF connection to ADAM CS with RJ-11 Back Panel FIGURE 7. Pin No.
Operation FIGURE 8. Cable for Connection of a UIO-256 or a Program Assign Panel Using an ADAM CS GPI Output to Operate a Relay (See Table 1 on page 15 for GPI Connector Pin-out) FIGURE 9.
UIO-256 Input/Output Frame GPI Input + 5-12 VDC Common EXTERNAL CIRCUIT Using an ADAM GPI Input (See Table 1 on page 15 for GPI Connector Pin-out FIGURE 10. FIGURE 11.
FIGURE 12.
UIO-256 Input/Output Frame Switch No. Description Default Settings ON=closed, OFF=open ON=closed, OFF=open AZedit baud rate selecta 1 OFF: 9600baud ON ON: 38.4k baud Keypanel incoming message optionb 2 OFF: Normal Operation OFF ON: All callers display in Incoming Message window Keypanel “in-use” and “busy” flashc 3 OFF: Enable OFF ON: Disable 4 Not Used, set to OFF OFF 5 Used to set Altera version ON 6 Not Used, set to OFF OFF Primary/Secondary card frame select. (ADAM systems only.
Operation ADAM CS Intercom Port Numbers Card 1 Card 2 Card 3 Card 4 Card 5 Card 6 Card 7 Card 8 Logical Keypanel Number (See Table X for DIP switch Settings) 1 9 17 25 33 41 49 57 1 2 10 18 26 34 42 50 58 2 3 11 19 27 35 43 51 59 3 4 12 20 28 36 44 52 60 4 5 13 21 29 37 45 53 61 5 6 14 22 30 38 46 54 62 6 7 15 23 31 39 47 55 63 7 8 16 24 32 40 48 56 64 8 (Grouped by Audio Input/Output Card Numbers) TABLE 3.
KP-32 Addressing UIO-256 Frame DIP Switch Settings Input/Output Range 1 2 3 4 5 6 7 8 #1 1-16 Open Closed Open Open Open Open Open Closed #2 17-32 Open Closed Open Closed Open Open Open Closed #3 33-48 Open Closed Open Open Closed Open Open Closed #4 49-64 Open Closed Open Closed Closed Open Open Closed TABLE 5.
Operation GPI Input Numbersa GPI Input Pin Numbersb UIO-256 UIO-256 UIO-256 UIO-256 Frame #1 Frame #2 Frame #3 Frame #4 1 17 33 49 9 34 2 18 34 50 10 35 3 19 35 51 11 36 4 20 36 52 12 37 5 21 37 53 13 38 6 22 38 54 14 39 7 23 39 55 15 40 8 24 40 56 16 41 DC Control Input “Minus” DC Control Input “Plus” 9 25 41 57 1 26 10 26 42 58 2 27 11 27 43 59 3 28 12 28 44 60 4 29 13 29 45 61 5 30 14 30 46 62 6 31 15 31 47
KP-32 Addressing TABLE 8. Planning Worksheet for ADAM CS with RJ-11 or DE9 Back Panel Description ADAM CS Connector No. ADAM CS Audio I/O Card No. Logical Keypanel J100 1 1 1 J101 1 2 2 J102 1 3 3 J103 1 4 4 J104 1 5 5 J105 1 6 6 J106 1 7 7 J107 1 8 8 J200 2 1 9 Port No.
Operation TABLE 8. Planning Worksheet for ADAM CS with RJ-11 or DE9 Back Panel Description ADAM CS Connector No. ADAM CS Audio I/O Card No.
TABLE 9. Planning Worksheet for ADAM CS with 50-pin Telco Back Panel ADAM CS Audio Input/ Output Card No.
TABLE 9. Planning Worksheet for ADAM CS with 50-pin Telco Back Panel ADAM CS Audio Input/ Output Card No.
27
