Operating Instructions
Table Of Contents
- CHAPTER 1 Introduction
- CHAPTER 2 BTR-800 Base Station
- CHAPTER 3 TR-800 Beltpack
- CHAPTER 4 TR-825 Beltpack
- CHAPTER 5 Initial Equipment Setup
- Unpacking
- Antenna Connection
- Antenna Polarization
- Distance between Antennas
- Antenna Placement
- Improving Reception and Increasing Range
- Base Station Set-up
- Location
- Power Connection
- Transmit Switches
- Internal Transmit Switches
- Intercom Switch
- Intercom Interface
- Dual Listen Functionality
- Auxiliary Input/Output
- Internal Auxiliary Input Routing Switch
- Stage Announce / Relay Contacts
- Base Station Link
- Beltpack Setup
- Antenna Connection
- Transmit Mode
- Headset Connection
- CHAPTER 6 Pre-Walk-Thru Checklist
- CHAPTER 7 System Operation
- Frequency Plan Overview
- Factory-Defined Groups
- User-Programmable Groups
- System Quick Start
- Base Station Operation
- Power
- Local Headset
- Portable Station Connect
- Intercom A and B
- Auxiliary
- Display Contrast
- BTR-800 Menu Structure
- Main Screen Flowchart
- Power-Up Screen
- Operating Screen
- Beltpack Activity Code Definitions
- Group/Channel Select
- Group/Frequency Select
- Frequency Edit (User-Programmed Groups Only)
- ClearScan™
- Special Key Sequences
- Lockout
- Copy
- 1st Use Default
- Factory Default
- Beltpack Operation
- On/Off and Volume Control
- Battery Check
- Talk Button
- Microphone Gain
- Audio Channel Select Button
- Stage Announce (SA)
- Wireless Talk Around (WTA)
- TR-800 Menu Structure
- Beltpack Menu Structure
- Power-Up Screens
- Group/Channel Screen
- Transmit Screen
- Receive 1 Screen
- Receive 2 Screen
- ClearScan™
- Stage Announce Enable/Disable
- Wireless Talk Around Enable/Disable
- Audio Channel A or B Disable/Enable
- Talk Button Latch on/Latch off
- Special Key Sequences
- Lockout
- 1st Use Default
- Factory Default
- TR-825 Menu Structure
- CHAPTER 8 System Walk-Thru
- CHAPTER 9 Troubleshooting
- CHAPTER 10 Tech Tips
- CHAPTER 11 Battery Information
- CHAPTER 12 Intercom Systems Specifications
- CHAPTER 13 Accessories and Replacement Parts
- CHAPTER 14 Certification Information
- CHAPTER 15 Three Band Base Stations
44 System Operation BTR-800, TR-800, TR-825
Group/Frequency Select
The Group/Frequency select screen allows a user to set the
group and select from a pre-determined number of frequencies
on each receiver. Each frequency displayed on the right half of
the screen corresponds to a channel number in the Group/
Channel Screen.
• Press [MENU] twice to go to the Group/Frequency Select
screen from the operating screen. Press [SET] to start the
group number flashing.
• Press the [UP]/[DOWN] arrows to change the group
number. The frequencies listed will reflect what is currently
in that group. Pressing [SET] will select the group and start
the selecting of predetermined frequencies within that
group. The R1 frequency will start flashing. NOTE: The
group number sets the transmit frequencies of factory
defined groups and these are not editable. In user-
programmed groups these are editable from the frequency
edit screen.
• Pressing the [UP]/[DOWN] arrows will change the
frequency of R1 to the pre-defined frequencies available.
Pressing [SET] will accept the change and move you to the
next channel to edit. If you had not press the arrow keys
when the frequency was flashing, but instead [press [SET],
you would have skipped to the next frequency to edit.
• After the last receive frequency is decided upon, pressing
[SET] will save that last frequency and start you over at the
beginning of the group/frequency select screen with nothing
flashing.
• Pressing [MENU] will take you to the operating screen if
this is a factory-defined group. If within a user programmed
group, you will be taken to the frequency edit screen.
NOTE: Pressing [MENU] after activity has occurred within
the screen will return to the group/frequency edit screen
with nothing flashing. Any change that had been done
before the last [SET] was pressed will be aborted.